Ublox MPCI-L2 series страница 57 Скачать руководство пользователя

Страница: 57 / 158

TOBY-L2 and MPCI-L2 series - System Integration Manual

UBX-13004618 - R07

Advance Information

System description

Page 57 of 158

1.12

Mini PCIe specific signals (W_DISABLE#, LED_WWAN#)

Mini PCI Express specific signals (

W_DISABLE#

LED_WWAN#

) are not available on TOBY-L2 series.

MPCI-L2 series modules include the

W_DISABLE#

active-low input signal to disable the radio operations as

specified by the

PCI Express Mini Card Electromechanical Specification

[15].

As described in Figure 25, the

W_DISABLE#

input is equipped with an internal pull-up to the

3.3Vaux

supply.

The

W_DISABLE#

input detailed electrical characteristics are described in the

MPCI-L2 series Data Sheet

[2].

Baseband
Processor

W_DISABLE#

MPCI-L2 series

3.3Vaux

W_DISABLE#

22k

Figure 25: MPCI-L2 series modules W_DISABLE# input circuit description

MPCI-L2 series modules include the

LED_WWAN#

active-low open drain output to provide the Wireless Wide

Area Network status indication as specified by the

PCI Express Mini Card Electromechanical Specification

[15].

For more electrical characteristics details see the

MPCI-L2 Data Sheet

[2].

1.13

Reserved pins (RSVD)

Pins reserved for future use, marked as

RSVD

, are not available on MPCI-L2 series.

TOBY-L2 series modules have pins reserved for future use, marked as

RSVD

: they can all be left unconnected on

the application board, except the

RSVD

pin number

that must be externally connected to ground.

1.14

Not connected pins (NC)

Pins internally not connected, marked as

, are not available on TOBY-L2 series.

MPCI-L2 series modules have pins internally not connected, marked as

: they can be left unconnected or they

can be connected on the application board according to any application requirement, given that none function is
provided by the modules over these pins.

Содержание MPCI-L2 series































































































































































Результаты поиска

Содержание MPCI-L2 series

Отзывы:

Похожие инструкции для MPCI-L2 series

Бренды по названию

Популярные бренды

Ublox MPCI-L2 series, Руководство по системной интеграции

Результаты поиска

Содержание MPCI-L2 series

Отзывы:

Похожие инструкции для MPCI-L2 series

Бренды по названию

Популярные бренды