Ublox MPCI-L2 series Скачать руководство пользователя | Manualshive

Страница: 141 / 158

background image

TOBY-L2 and MPCI-L2 series - System Integration Manual

UBX-13004618 - R07

Advance Information

Approvals

Page 141 of 158

4.2

Federal Communications Commission and Industry Canada notice

Federal Communications Commission (FCC) IDs:



u-blox TOBY-L200 cellular modules:

XPYTOBYL200



u-blox TOBY-L201 cellular modules:

XPYTOBYL201



u-blox TOBY-L210 cellular modules:

XPYTOBYL210



u-blox TOBY-L280 cellular modules:

XPYTOBYL280



u-blox MPCI-L200 cellular modules:

Contains FCC ID XPYTOBYL200



u-blox MPCI-L210 cellular modules:

Contains FCC ID XPYTOBYL210

Industry Canada (IC) Certification Numbers:



u-blox TOBY-L200 cellular modules:

8595A-TOBYL200



u-blox TOBY-L201 cellular modules:

8595A-TOBYL201



u-blox TOBY-L210 cellular modules:

8595A-TOBYL210



u-blox TOBY-L280 cellular modules:

8595A-TOBYL280



u-blox MPCI-L200 cellular modules:

Contains IC 8595A-TOBYL200



u-blox MPCI-L210 cellular modules:

Contains IC 8595A-TOBYL210

4.2.1

Safety warnings review the structure



Equipment for building-in. The requirements for fire enclosure must be evaluated in the end product



The clearance and creepage current distances required by the end product must be withheld when the
module is installed



The cooling of the end product shall not negatively be influenced by the installation of the module



Excessive sound pressure from earphones and headphones can cause hearing loss



No natural rubbers, hygroscopic materials, or materials containing asbestos are employed

4.2.2

Declaration of Conformity

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:



this device may not cause harmful interference



this device must accept any interference received, including interference that may cause undesired operation

Radiofrequency  radiation  exposure  Information:  this  equipment  complies  with  radiation
exposure limits prescribed for an uncontrolled environment for fixed and mobile use conditions.
This equipment should be installed and operated  with a minimum distance of 20 cm between
the  radiator  and  the  body  of  the  user  or  nearby  persons.  This  transmitter  must  not  be  co-
located or operating in conjunction with any other antenna or transmitter except as authorized
in the certification of the product.

The gain of the system antenna(s) used for the TOBY-L2 and MPCI-L2 series modules except for
TOBY-L201 (i.e. the combined transmission line, connector, cable losses and radiating element
gain) must not exceed 9.8 dBi (700 MHz, i.e. LTE FDD-17 band), 4.3 dBi (850 MHz, i.e. GSM 850 or
UMTS FDD-5 or LTE FDD-5 band), 5.5 dBi (1700 MHz, i.e. AWS or UMTS FDD-4 or LTE FDD-4
band), 2.8 dBi (1900 MHz, i.e. GSM 1900 or UMTS FDD-2 or LTE FDD-2 band), 6.0 dBi (2500 MHz,
i.e. LTE FDD-7 band) for mobile and fixed or mobile operating configurations.

«
...
139
140
141
142
143
...
»

Содержание MPCI-L2 series































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPCI-L2 series

Бренд: DayTronic Страницы: 22

Бренд: DayTronic Страницы: 414

Бренд: H3C Страницы: 5

Бренд: H3C Страницы: 4

Бренд: Parkside Страницы: 86

Бренд: Velleman Страницы: 26

Бренд: Velleman Страницы: 32

Бренд: Velocity Страницы: 84

Бренд: SYR Страницы: 2

Q Module WFZ16.Ox

Бренд: QUNDIS Страницы: 24

Бренд: Monster Central Страницы: 13

Бренд: Rain Bird Страницы: 18

Бренд: Quickie Страницы: 64

Бренд: Kamstrup Страницы: 7

Бренд: Xylem Страницы: 28

Бренд: Bardiani Страницы: 80

Бренд: Overland Storage Страницы: 4

Бренд: Powtran Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды