Ublox MAX-M10 страница 84 Скачать руководство пользователя | Manualshive

Страница: 84 / 92

background image

MAX-M10M - Integration manual

Feature

Change

Action needed / Remarks

Unique chip identiﬁer

A unique chip identiﬁer output in boot screen and in the UBX-
SEC-UNIQID message.

Code change (optional))

Conﬁguration lock

New security feature that is enabled with CFG-SEC-CFG_LOCK
message for locking the receiver conﬁguration.

Code change (optional)

Table 34: MAX-M10M software features

Refer to the ﬁrmware Release notes [

] and the Interface description [

] for more information on

supported features and messages in u-blox M10 receiver.

B Reference designs

The

External components

section provides the speciﬁcation and recommendations for the external

components that are shown in each reference design.

This section provides some reference designs for typical and antenna supervisor design cases.

Designs with 1.8 V main supply or with independent supply for VCC and V_IO must fulﬁll certain
requirements when transitioning to hardware backup mode. Refer to

Supply design examples

for more details.

B.1 Typical design

Here are some key features for a MAX-M10M typical design:
• VCC and V_IO are connected together to a single supply. In designs with 3.3 V supply, the VIO_SEL

pin must be left open, as shown in

. In designs with 1.8 V supply, the VIO_SEL pin must

be connected to GND, as shown in

• V_BCKP supply is optional. If present, the hardware backup mode is supported. This mode

maintains the time and GNSS orbit data in the battery-backed RAM memory if the main supply
is switched oﬀ.
If there is no backup supply, time aiding with the UBX-MGA-INI-TIME_UTC message (optionally
with a timing signal at the EXTINT pin) and the GNSS orbit data from the AssistNow services or
stored on the host controller can be used to reduce the TTFF.

• This design uses an active antenna, which can be supplied either with the VCC_RF output from

MAX-M10M, as shown in

, or from an external supply, as shown in

. It is also

possible to use a passive antenna in the design. Only use a good quality passive antenna to avoid
performance degradation compared to an active antenna setup.

• UART and I2C communication interfaces are available.
• For an absolute minimum design using UART, other PIOs (RESET_N, EXTINT, TIMEPULSE, SDA,

SCL, SAFEBOOT_N) can be left open.

UBX-22038241 - R02

Appendix

Page 84 of 92

C1-Public

«
...
82
83
84
85
86
...
»

Содержание MAX-M10





























































































Отзывы:

Нет отзывов

Похожие инструкции для MAX-M10

Бренд: ABATEC Страницы: 8

Бренд: Wavetec Страницы: 17

Бренд: Calsense Страницы: 9

Smart Controller

Бренд: MaestroHome Страницы: 10

Бренд: GAUGEMASTER Страницы: 2

Бренд: EasyIO Страницы: 19

Бренд: Zero 88 Страницы: 2

Бренд: Zenit Страницы: 24

Бренд: UCS Страницы: 4

Бренд: Gascat Страницы: 32

Бренд: Walimex Pro Страницы: 68

Бренд: Union Instruments Страницы: 63

Бренд: YOKOGAWA Страницы: 150

Бренд: YOODA Страницы: 3

Бренд: YMGI Страницы: 8

UNDER CONTROL CP-30A PILOT

Бренд: G-Force Страницы: 2

Бренд: Dantel Страницы: 6

GAMMA VERSUS Series

Бренд: JCM Страницы: 111

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды