Ublox MAX-M10 Скачать руководство пользователя | Manualshive

Страница: 50 / 92

background image

MAX-M10M - Integration manual

Figure 17: Time pulse and TIM-TP

3.9.2 Time pulse conﬁguration

The time pulse (TIMEPULSE) signal has conﬁgurable pulse period, length and polarity (rising or
falling edge).

It is possible to deﬁne diﬀerent signal behavior (i.e. output frequency and pulse length) depending
on whether or not the receiver is locked to reliable time source.

The conﬁguration group CFG-TP-* can be used to change the time pulse settings, and includes the
following parameters deﬁning the pulse:

•

time pulse enable

- If this item is set, the time pulse is active.

•

frequency/period type

- Determines whether the time pulse is interpreted as frequency or

period.

•

length/ratio type

- Determines whether the time pulse length is interpreted as length [us] or

pulse ratio [%].

•

antenna cable delay

- Signal delay due to the cable between the antenna and the receiver.

•

pulse frequency/period

- Frequency or pulse time period when locked mode is not conﬁgured or

not active.

•

pulse frequency/period lock

- Frequency or pulse time period for locked mode. In use as soon as

the receiver has calculated a valid time from a received signal. Only used if the corresponding
item is set to use another setting in locked mode.

•

pulse length/ratio

- Length or duty cycle of the generated pulse, speciﬁes either time or ratio

for the pulse to be on/oﬀ.

•

pulse length/ratio lock

- Length or duty cycle of the generated pulse for locked mode. In use

as soon as the receiver has calculated a valid time from a received signal. Only used if the
corresponding item is set to use another setting in locked mode.

•

user delay

- The cable delay from the receiver to the user device plus signal delay of any user

application.

•

lock to GNSS freq

- If this item is set, uses the frequency gained from the GNSS signal

information rather than the local oscillator's frequency.

•

locked other setting

- If this item is set, the alternative setting is used as soon as the receiver

can calculate a valid time. This mode can be used, for example, to disable time pulse if the time
is not locked, or to indicate a lock with diﬀerent duty cycles.

•

align to TOW

- If this item is set, pulses are aligned to the top of a second.

•

polarity

- If set, the ﬁrst edge of the pulse is a rising edge (pulse polarity: rising).

•

grid UTC/GNSS

- Selection between UTC (0), GPS (1), GLONASS (2), BeiDou (3), (4) Galileo and

NAVIC (5) time grid. Also aﬀects the time output by UBX-TIM-TP message.

The maximum pulse length cannot exceed the pulse period.

UBX-22038241 - R02

3 Receiver functionality

Page 50 of 92

C1-Public

«
...
48
49
50
51
52
...
»

Содержание MAX-M10





























































































Отзывы:

Нет отзывов

Похожие инструкции для MAX-M10

Бренд: GE Страницы: 2

Бренд: XOXO Modular Страницы: 13

Бренд: Balboa Water Group Страницы: 28

Бренд: GBD Страницы: 68

Бренд: BADODOSECURITY Страницы: 8

Бренд: Lawler Страницы: 6

Бренд: Data Aire Страницы: 28

Бренд: Harsco Industrial Страницы: 57

Бренд: C&C Страницы: 17

Бренд: hager Страницы: 2

Бренд: hager Страницы: 4

Бренд: Vag Страницы: 15

Бренд: Abocom Страницы: 10

Бренд: HomeMatic Страницы: 36

Бренд: Kohler Страницы: 48

AUTOPULSE IQ-318

Бренд: Notifier Страницы: 62

Бренд: Argo-Hytos Страницы: 38

Бренд: Anest Iwata Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды