background image

US Distributor: 1-800-209-4177

III. Setting Up the Machine

When first opening the induction heating machine, be very careful remov-

ing the machine from the box. It is a heavy piece of equipment. The ma-

chine comes with one assembled coil, and one piece of copper tubing 

for making your own coil. 

Start by connecting the assembled coil to the machine. It is important that 

it is screwed on tightly, as water will be running through the coil. Be sure to 

use a wrench to tighten bolts.

Once the coil is connected, water inputs and outputs can begin being 

routed. Depending on the model you have, the number of water inputs 

and water outputs may vary. One hose is provided for you, but it is possi-

ble more hosing will be needed. This can be found at any hardware store. 

The Induction Heating Machine does not need a water circulator or water 

chiller. In fact, it is recommended to be used simply with clean tap water. 

It is important that the water hookup is both pressurized and contains 

clean and clear tap water. Excessively dirty water will lead to breakdown 

of the machine.

For the water inputs, a splitter may be used so a single water source can 

provide water for the whole machine.  For the outputs, it is important that 

each water output is run separately, with no connectors. Problems can 

occur if output hoses are connected to one another.

Once the hoses are setup, the wiring needs to be setup. For the 110 V 

model, make sure the wire you use is at least 14 gauge For the 220V 

model, make sure the wire is at least 6 gauge.  Connect the ground wire 

to the designated place on the back of the machine. Similarly for the two 

live wires. Make sure there is no wire exposed from the connections, as this 

could present a potential fire or electrical hazard. 

The foot pedal should be hooked up next. The place for the foot pedal is 

on the front of the machine, and the foot pedal should be setup on the 

floor.

It is important that the machine is setup in a place free of debris and clut-

ter.  The floors should also be kept clear. Make sure hoses and wires for the 

machine are all secured to avoid tripping hazards.   

4

Содержание USS-HFIH00001















Отзывы: