U-Line UCBR532-SS01A Скачать руководство пользователя

Страница: 47 / 49

USER GUIDE

Remove Fan and Cover

Evaporator Fan Replacement

1. Disconnect power from the unit before

starting.

Remove the front cover grille. Take out the

two upper and two lower screws. Disconnect the power
cord from the back of the

2. Remove the evaporator box cover. Take out the four

long screws and set the cover aside, exposing the
evaporator compartment.

3. Remove the evaporator air deflector cooling baffle by

sliding it out and set aside.

4. Remove (4) screws to detach fan assembly from

assembly from mounting bracket assembly.

5. Grab ahold of each fan assembly and push toward the

interior of the unit to remove the motor shaft from the
rubber gasket.

Upper grille screws

Lower grille screws

Set grille aside

Remove (4) Screws

Содержание UCBR532-SS01A


















































Результаты поиска

Содержание UCBR532-SS01A

Отзывы:

Похожие инструкции для UCBR532-SS01A

Бренды по названию

Популярные бренды

U-Line UCBR532-SS01A, Руководство пользователя и сервисное руководство

Результаты поиска

Содержание UCBR532-SS01A

Отзывы:

Похожие инструкции для UCBR532-SS01A

Бренды по названию

Популярные бренды