U-Line UACR015 Скачать руководство пользователя | Manualshive

Страница: 12 / 44

background image

USER GUIDE

u-line.com

Grille Installation

Grille Installation

REMOVING AND INSTALLING GRILLE

Disconnect electric power to the unit before
removing the grille.

When using the unit, the grille must be installed.

WARNING

!

DO NOT touch the condenser fins. The condenser
fins are SHARP and can be easily damaged.

Removing the grille

1. Disconnect power to the unit.

2. Open unit door.

3. Remove the center screw.

4. Remove grille by sliding grille up and pulling it toward

you.

Installing the grille

1. Open unit door.

2. Align grille with front of unit slide front tab on grille

behind front of base.

3. Install center screw.

4. Reconnect power to the unit.

WARNING

!

3

12

«
...
10
11
12
13
14
...
»

Содержание UACR015













































Отзывы:

Нет отзывов

Похожие инструкции для UACR015

Бренд: Yonanas Страницы: 32

Бренд: Saeco Страницы: 56

Бренд: Saeco Страницы: 8

Бренд: Rancilio Страницы: 2

Бренд: Saeco Страницы: 62

Бренд: Saeco Страницы: 43

Бренд: Waring Страницы: 19

Бренд: Hoshizaki Страницы: 33

Бренд: BOSKA Страницы: 9

Бренд: Beper Страницы: 44

Бренд: NewAir Страницы: 11

Бренд: U-Line Страницы: 36

Бренд: Ratio Страницы: 21

Бренд: Hoshizaki Страницы: 88

Бренд: Myria Страницы: 40

Series 8400 bistro

Бренд: WMF Страницы: 47

Бренд: Blodgett Страницы: 2

Бренд: Saeco Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды