U-Line U-2224BEV Скачать руководство пользователя | Manualshive

Страница: 14 / 62

background image

USER GUIDE

Grille - Plinth Installation 1

u-line.com

SAFETY •

INSTALLATION & INTEGRATION

• OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE

Grille - Plinth Installation

REMOVING AND INSTALLING GRILLE
(PLINTH STRIP/BASE FASCIA)

WARNING

!

Disconnect electric power to the unit before
removing the grille (plinth strip/base fascia).

When using the unit, the grille (plinth strip/base
fascia) must be installed.

WARNING

!

DO NOT touch the condenser fins. The condenser
fins are SHARP and can be easily damaged.

Removing the grille
(plinth strip/base fascia)

1. Disconnect power to the unit.

2. Loosen the two screws (1).

3. Remove grille (plinth strip/base fascia) (2) from unit.

Installing the grille

1. Align cabinet and grille holes and secure, but do not

over tighten grille (plinth strip/base fascia) screws (1).

2. Reconnect power to the unit.

1

2

14

«
...
12
13
14
15
16
...
»

Содержание U-2224BEV































































Отзывы:

Нет отзывов

Похожие инструкции для U-2224BEV

Бренд: MAGIMIX Страницы: 14

Бренд: KitchenFun Страницы: 20

Бренд: Caffitaly System Страницы: 40

Бренд: Blaupunkt Страницы: 80

Бренд: Avintage Страницы: 110

Nicer Dicer FUSION SMART

Бренд: Genius Страницы: 16

Бренд: Omcan Страницы: 16

Бренд: Atag Страницы: 44

S 4232 Family Black

Бренд: ECG Страницы: 64

Бренд: Sammic Страницы: 52

Бренд: Roller Grill Страницы: 32

Бренд: ENKHO Страницы: 40

Pizzarette PO-102929

Бренд: emerio Страницы: 44

Бренд: Marta Страницы: 13

Бренд: Orava Страницы: 19

Бренд: Klarstein Страницы: 76

All My Love Heart Shortbread Cookies 65587/65577

Бренд: Easy-Bake Страницы: 4

COMPETENCE 5005

Бренд: AEG Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды