background image

1120 IH-3745

PAGE 1 OF 6

6' ALUMINUM 
PICNIC TABLE

1-800-295-5510

 uline.com

π  H-3745

1.  Lay three aluminum planks side by side, upside 

down, on a flat surface to form the tabletop. Slide 

the metal caps onto each end. One end cap 

covers the three planks. The pre-drilled holes of the 

end cap should be facing up. Use power drill and 

two self-tapping  

screws to secure  

each metal end  

cap onto each  

end of the tabletop.  

Loosely attach the  

center support brace,  

centered, onto the  

middle tabletop plank  

using two hold down  

clips, two 5/16" flange  

nuts and two 5/16"  

carriage bolts.  

(See Figure 1) 

 

2.  For the seats, lay two aluminum  

planks upside down on a flat  

surface. Slide the metal end caps 

onto each end of the planks.  

The pre-drilled holes of the end cap 

should be facing up. Use power 

drill and two self-tapping screws to  

secure each end cap onto each 

end of the plank.  

(See Figure 2)

3.  Loosely attach both 

diagonal braces to 

both leg frames using 

one 3/8" flange nut  

and one 3/8" hex head 

bolt per leg frame. 

(See Figure 3)    

 

 

Diagonal 

Brace

Center Support Brace

Metal End Cap

Hold Down Clip

TOOLS NEEDED

Power Drill

Socket Wrench

PARTS

ASSEMBLY INSTRUCTIONS

Aluminum Plank x 5 

Metal End Caps for Tabletop x 2

Hold Down Clips x 22

Diagonal Brace x 2

3/16" Self-Tapping  

Screws x 12

Center Support Brace x 1

Leg Frame x 2

3/8" Flange Nuts x 3

5/16" Flange Nuts x 22

Figure 2

Figure 1

5/16" x 1½" Carriage Bolts x 22

3/8” x 1⁄" Hex Head Bolts x 3

Metal End Caps for Seats x 4

Figure 3

Para Español, vea páginas 3-4.

Pour le français, consulter les pages 5-6.

Содержание H-3745







Отзывы: