U-Line H-1028 Скачать руководство пользователя страница 4

 

PHONE 1-800-295-5510   

FAX 1-800-295-5571  

WEB uline.com

 

SAFETY INSTRUCTIONS 

 

1.  Read the manual and understand all safety instructions before operating the 

tool.  If you have questions, contact Uline at 1-800-295-5510. 

2.  Never use flammable gases as a power source for the stapler.  Only use 

filtered, compressed air. 

3.  Never use gasoline or other flammable liquids to clean the stapler.  Vapors 

left on the stapler could ignite and cause the tool to explode 

4.  Do not exceed 110 psi of air pressure when operating the stapler. 
5.  Disconnect the stapler for the air supply before making adjustments, 

cleaning or clearing jams and when not in use. 

6.  Do not pull the trigger when carrying or holding the stapler. 
7.  Never carry the stapler by the hose or pull on the hose to move the stapler. 
8.  Always wear protective equipment, i.e. safety glasses, hearing protection 

and head protection. 

9.  Do not use a check valve or any other fitting which allows air to remain in the 

stapler. 

10. Do not place your hand or any other body part in the staple clinching area or 

adjustment window when connecting or disconnecting the air supply.   

11. Never point the stapler at yourself or anyone else. 

 

Back to Top

 

        CHICAGO 

 MINNEAPOLIS 

LOS ANGELES 

NYC/PHILA

ATLANTA 

 DALLAS

Содержание H-1028

















Отзывы: