U-Line 2260DC Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 70

background image

USER GUIDE

Troubleshooting - Extended 1

u-line.com

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE •

SERVICE

Troubleshooting - Extended

CAUTION

!

Never attempt to repair or perform maintenance
on the unit until the main electrical power has
been disconnected from the unit.

SPECIFIC ERRORS AND ISSUES

The technically advanced diagnostic capabilities of the
electronic controls utilized on the 1200 and 2200 series
units allows for easy and thorough troubleshooting.

Navigation of the control is the key and is explained in the
CONTROL OPERATION section of the manual, along with
control button layout, control function descriptions, a
service mode menu and service menu selection
explanations.

Verification of temperature and thermistor performance
can be identified by directly viewing thermistor readings in
the service mode.

Component failure issues can be identified through service
mode menu #19, “Component Testing.” Individual
components can be switched on and off to check for both
proper function of a specific component and also delivery
of supply voltage to the components through the relays
and DC outputs located on the relay/power board.

Included in this section are some diagnostic tips and of
course, if additional help is required please contact the
U-Line Corp, “Customer Care Facility” at +1.800.779.2547
for assistance.

NORMAL OPERATING SOUNDS

All models incorporate rigid foam insulated cabinets to
provide high thermal efficiency and maximum sound
reduction for its internal working components. Despite this
technology, your model may make sounds that are
unfamiliar.

Normal operating sounds may be more noticeable because
of the unit’s environment. Hard surfaces such as cabinets,
wood, vinyl or tiled floors and paneled walls have a
tendency to reflect normal appliance operating noises.

Listed below are common refrigeration components with a
brief description of the normal operating sounds they
make. NOTE: Your product may not contain all the
components listed.

• Compressor: The compressor makes a hum or pulsing

sound that may be heard when it operates.

• Evaporator: Refrigerant flowing through an evaporator

may sound like boiling liquid.

• Condenser Fan: Air moving through a condenser may

be heard.

• Automatic Defrost Drain Pan: Water may be heard

dripping or running into the drain pan when the unit is
in the defrost cycle.

Solenoid Valves: An occasional clicking sound may be
heard as solenoid valves are operated.

55

«
...
53
54
55
56
57
...
»

Содержание 2260DC







































































Отзывы:

Нет отзывов

Похожие инструкции для 2260DC

Бренд: Heinner Страницы: 117

Бренд: ETNA Страницы: 13

Бренд: Ningbo Yingqi Metal Products Страницы: 10

Бренд: Gaggenau Страницы: 96

Бренд: Lec Страницы: 21

JUD24FR*S series

Бренд: Jenn-Air Страницы: 56

Бренд: Omcan Страницы: 100

Бренд: Vivax Страницы: 84

Бренд: Blomberg Страницы: 294

FRIGOMATIC 35F - 50F

Бренд: Frigoboat Страницы: 20

Бренд: Frigidaire Страницы: 13

Бренд: Frigidaire Страницы: 3

Бренд: Frigidaire Страницы: 3

Бренд: Frigidaire Страницы: 2

Бренд: Frigidaire Страницы: 2

Бренд: Frigidaire Страницы: 2

Бренд: Frigidaire Страницы: 12

Бренд: Frigidaire Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды