manualshive.com logo in svg

U-Line 124BEV, Руководство пользователя и сервисное руководство

Поделиться
Скачать
U-Line 124BEV Скачать руководство пользователя страница 48

USER GUIDE

 R-600A Specifications 1

u-line.com

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • 

SERVICE

R-600A Specifications

For R-600a refrigerant service tips and more videos, go 
to: 

www.u-line.com/videos

. 

WARNING

!

Flammability warnings for a pure-iso-butane 
refrigerant.

Technician must observe all federal, state and local laws regarding refrigerants.

Gloves and Eye Protection must be used.

R-600a is considered non-toxic, but is flammable 
when mixed with air.

Keep a dry powder type fire extinguisher in the 
work area.

R-600a is heavier than air, do not allow any 
leakage/migration to low areas such as 
basements and stairs.

Never use a torch on a fully charged 
refrigeration system.

Never substitute U-Line OEM replacement parts 
or methods of construction.

R-600a must be stored and transported in 
approved containers.

48

Содержание 124BEV






































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды