background image

409-1993

AMP-TAPETRONIC Machine 69875 and 69875-1

Rev J

10 of 46

Tyco Electronics Corporation

3. RECEIVING INSPECTION AND INSTALLATION
3.1. Receiving Inspection

The machine is thoroughly inspected during and after assembly. Before it is shipped, final tests and inspections
are made to ensure proper functioning. Still, the following inspection should be performed as a safeguard
against problems generated during shipment.

1. Carefully uncrate the machine and place it on a sturdy bench where there is enough light to permit a
careful examination.

2. Thoroughly inspect the entire machine for evidence of damage that may have occurred during transit.
If the machine is damaged, file a claim against the carrier and notify Tyco Electronics immediately.

3. Check all components and parts to be certain they are secure.

4. Check all wiring for loose connections and for frayed or broken wire and insulation.

5. If applicable, check all air lines for evidence of loose connections or leaks.

It is IMPORTANT that this manual, other documents shipped with the machine (e.g., drawings, parts lists, etc.), and

any enclosed product samples remain with the machine for the benefit of personnel responsible for installation,

operation, and maintenance.

3.2. Considerations Affecting Machine Placement

The location of the machine in relation to the operator is essential to both safety and efficiency. Studies have
repeatedly shown that fatigue will be reduced and efficiency increased if particular attention is paid to the
bench, the operator’s chair, and the placement of the foot switch if one is used.

A. Bench

A sturdy bench, 711 to 762 mm [28 to 30 in.] high, aids comfort by allowing the operator’s feet to rest on
the floor. The operator’s weight and leg position can be easily shifted. The bench should have rubber
mounts to reduce noise. The open area under the bench should allow the chair to slide far enough in for
the operator’s back to be straight and supported by the back rest.

B. Machine Location on Bench

The machine should be located near the front of the bench and the tooling area (the area where product is
applied) should be 152 to 203 mm [6 to 8 in.] from the front edge. Access to the back of the machine must
be provided.

C. Operator's Chair

The operator’s chair should swivel, and the seat and back rest should be padded and independently
adjustable. The back rest should be large enough to support the back both above and below the waist.

In use, the chair should be far enough under the bench so that the operator’s back is straight and
supported by the back rest.

D. Foot Switch

When the operator is correctly positioned in front of the machine, the foot should rest on the switch
comfortably and easily. The switch should be placed on a rubber mat. This allows the switch to be
movable and permits the operator to shift positions to minimize fatigue. At the same time the mat prevents
the switch from sliding unintentionally.

The preference for locating the switch varies among operators. Some like the switch located so that their
foot rests on the switch when their legs are in the natural sitting position (calf perpendicular to the floor).
Others prefer it slightly in front of the natural position. The important thing is that the foot be about 90

_

 to

the calf when resting on the switch. Those who prefer the switch slightly forward may require a
wedge–shaped block placed under it.

NOTE

i

Содержание AMP-TAPETRONIC 69875















































Отзывы: