background image

1

http://www.tyan.com

Tomcat i815ef S2425

User’s Manual

Revision 1.00

Copyright © TYAN Computer Corporation, 2001. All rights reserved. No part of this manual may
be reproduced or translated without prior written consent from TYAN Computer Corp.

All registered and unregistered trademarks and company names contained in this manual are
property of their respective owners including, but not limited to the following.

TYAN, Tomcat S2425 are trademarks of TYAN Computer Corporation.
Intel, Intel Pentium, i815, combinations thereof are trademarks of Intel Corporation.
AMI, AMIBIOS are trademarks of American Megatrends Inc.
Microsoft, Windows are trademarks of Microsoft Corporation.
IBM, PC, AT, PS/2 are trademarks of IBM Corporation.
Winbond is a trademark of Winbond Electronics Corporation.
Micronics is a trademark of Micronics Corporation.
Portable Document Format (PDF) is a trademark of Adobe Corporation.

Information contained in this document is furnished by TYAN Computer Corporation and has been
reviewed for accuracy and reliability prior to printing. TYAN assumes no liability whatsoever, and
disclaims any express or implied warranty, relating to sale and/or use of TYAN products including
liability or warranties relating to fitness for a particular purpose or merchantability. TYAN retains
the right to make changes to product descriptions and/or specifications at any time, without notice.
In no event will TYAN be held liable for any direct or indirect, incidental or consequential damage,
loss of use, loss of data or other malady resulting from errors or inaccuracies of information
contained in this document.

Содержание S2425













































Отзывы: