Tuttnauer Elara11 Скачать руководство пользователя страница 17

Страница: 17 / 109

Page 16

•

Door is made of stainless steel 316.

•

Trays are made of stainless steel 304.

•

Water reservoir is made of polyethylene.

•

Door handle and door cover are made of hard plastic material, which is

safe to touch and thermo-insulated.

1.20.

Stickers Description

Symbol

Meaning

Part Number

Location

Pour distilled water into the
reservoir through the opening
on top of the autoclave until it
reaches 1" below the bottom
of the base of the safety
valves.

LAB048-0355

Near the mineral-free
water reservoir cover

Caution! Hot
steam.

LAB048-0058

Near the safety valve

Do not pour water into this
reservoir.

Near the wastewater
reservoir cover

Caution! Consult
accompanying
documents

LAB048-0024

Near the Power switch

PUSH
TO
RESET

Resetting the cut-
off

LAB048-0018

Near the cut-off

Protective Earth
(Ground)

LAB048-0020

Near the on/off switch

Caution: Hot
surface

LAB048-0023

On the top cover above
the door and on the rear
cover above the water
strainer

Содержание Elara11














































































































Результаты поиска

Содержание Elara11

Отзывы:

Похожие инструкции для Elara11

Бренды по названию

Популярные бренды

Tuttnauer Elara11, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание Elara11

Отзывы:

Похожие инструкции для Elara11

Бренды по названию

Популярные бренды