Tuttnauer AMS10-120-T Скачать руководство пользователя страница 97

Страница: 97 / 104

12.2

Chamber clean Cleaning procedure

Important

The Chamber Clean cleaning program for class B and S for T-Edge10
autoclaves is described below:

The chamber must be cold.

1. All steps in this procedure must be completed without interruption.

2. Open the autoclave chamber door.

3. Remove instruments and any load, trays from the autoclave

chamber.

4. Place the trays and tray holder in the sink to be cleaned with a

stainless steel Safe cleaner.

5. Place one 6g cleaning tablet (1) from the tablet packing (2) inside

the sterilization chamber at the back bottom of the cold chamber.
(see figure below). Under the 269°F (132°C) program conditions.
Chamber clean program 6g Tablet position

6. Close the autoclave door.

7. Fill fully (Approx. 777 Ounces for T- Edge 10) clean water

reservoir with

distilled water only

. (Either Automatic or manual

filling). For manual filling, select 0, Global select 1 for automatic
filling. Fill the reservoir full until the screen indicate full.

Page 90

Содержание AMS10-120-T









































































































Результаты поиска

Содержание AMS10-120-T

Отзывы:

Похожие инструкции для AMS10-120-T

Бренды по названию

Популярные бренды

Tuttnauer AMS10-120-T, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание AMS10-120-T

Отзывы:

Похожие инструкции для AMS10-120-T

Бренды по названию

Популярные бренды