Turnstiles Traffic H1 Скачать руководство пользователя страница 56

Страница: 56 / 101

Assembling flange and barrier arm

5816,0013US / Version 02

9.2

Check swivel range, set close direction and mount flange

Secure barrier danger area e.g. with barrier tape.

Remove rear cover of the barrier housing.



See page 41, chapter 7.5.

Remove rear door of the barrier housing.

Switch on power supply.

Switch on the barrier if required.



See page 65, chapter 10.4.

Switch on Mode "Service "

Switch the "Service" switch on the control unit. The LED lights
red. The display backlighting flashes.



See page 65, chapter 10.4.

Check the swivel range of the
barrier arm

Opening and closing the barrier manually; Check the swivel
range via the shaft.



Middle left button : Manually open the barrier.



Middle right button

: Manually close the barrier.

Setting the close direction

If the close direction is incorrect, change the close direction
via the parameter "Close direction".



See separate

document "Description of control units MGC and MGC Pro for
MHTM

MicroDrive barriers", chapter "Close direction".

WARNING!
Danger of crushing between flange and barrier housing!

Switch off power supply. Ensure that the system is powered
down. Secure against reactivation.

Traffic H1 Swing Gate Horizontal Barrier

www.TURNSTILES.us | [email protected] | 303-670-1099

Содержание Traffic H1






































































































Результаты поиска

Содержание Traffic H1

Отзывы:

Похожие инструкции для Traffic H1

Бренды по названию

Популярные бренды

Turnstiles Traffic H1, Руководство по эксплуатации

Результаты поиска

Содержание Traffic H1

Отзывы:

Похожие инструкции для Traffic H1

Бренды по названию

Популярные бренды