Turf Equipment Z-SPRAY Скачать руководство пользователя страница 12

Страница: 12 / 64

Specifications

Systems

Engine

•

Engine Specifications: See your Engine Owner’s
Manual

•

Engine Oil Type: 4-Cycle Premium Engine Oil

•

RPM: Full Speed: 3600 ±100 RPM (No Load)

Fuel System

•

Capacity: 5 gal. (18.9 L)

•

Fuel Recommendations:

– For best results, use only clean, fresh, unleaded

gasoline with an octane rating of 87 or higher
((R+M)/2 rating method).

– Oxygenated fuel with up to 10% ethanol or

15% MTBE by volume is acceptable.

–

Do Not

use ethanol blends of gasoline (such

as E15 or E85) with more than 10% ethanol
by volume. Performance problems and/or
engine damage may result which may not be
covered under warranty.

–

Do Not

use gasoline containing methanol.

–

Do Not

store fuel either in the fuel tank or

fuel containers over the winter unless a fuel
stabilizer is used.

–

Do Not

add oil to gasoline.

•

Fuel Filter: In fuel tank

Electrical System (Electric Start)

•

Charging System: Flywheel Alternator

•

Charging Capacity: 20 amps

•

Battery Type: BCI Group U1

•

Battery Voltage: 12 Volt

•

Polarity: Negative Ground

•

Fuses:

– 10 amp main fuse

– 30 amp sprayer fuse

– 1 amp speedometer fuse

Safety Interlock System

Engine will not start unless the interlock key is
installed in the OPC switch.

Operator Controls

Steering and Motion Control:

•

Moving the steering control from side to side
controls right and left travel.

•

One lever in the center of the steering control,
controls both drive wheels for moving forward or
reverse, stopping, and power turning.

•

Motion control lever automatically returns to the
neutral position if released.

Transmission

•

Tandem hydro gear variable displacement high
efficiency pumps coupled with two high efficiency
Parker wheel drive motors.

•

Hydraulic Oil: Use 15W-50.

•

Hydraulic Oil Capacity: 2.5 qt (2.4 L)

•

Hydraulic filter is replaceable, cartridge type

•

Speeds:

– 0-8.0 mph (12.9 km/hr) forward.

– 0-4.0 mph (6 km/hr) reverse.

•

Drive wheel release valve allows machine to be
moved when engine is not running.

Wheel Drive System

Drive wheels are direct coupled to Parker wheel drive
motors with 1.25 inch (31.75 mm) tapered shaft.

Содержание Z-SPRAY

































































Результаты поиска

Содержание Z-SPRAY

Отзывы:

Бренды по названию

Популярные бренды

Turf Equipment Z-SPRAY, Руководство оператора

Результаты поиска

Содержание Z-SPRAY

Отзывы:

Бренды по названию

Популярные бренды