turck TBEN-S2-4IOL Скачать руководство пользователя страница 120 | Manualshive

Страница: 120 / 134

turck TBEN-S2-4IOL Скачать руководство пользователя страница 120

Operating

Software diagnostic messages

120

Hans Turck GmbH & Co. KG | T +49 208 4952-0 | F +49 208 4952-264 | [email protected] | www.turck.com

LED DXP 1, 3, 5, 7

Meaning (input)

Meaning (output)

Off

Input not active

Output not active

Green

Input active

Output active (max. 2 A)

Red

–

Output active with overload/short
circuit

ERR DXP 7

Meaning

White flashing

Wink command active

10.4

Software diagnostic messages

The device provides the following software diagnostic messages:

n

DSP diagnostics
Diagnostic messages of the universal digital channels of the module (DXP 1, 3, 5, 7).

n

IO-Link master diagnostics
The IO-Link master reports problems within the IO-Link communication.

n

IO-Link device diagnostics
The device diagnostics map the IO-Link Event Codes (according to the IO-Link specification)
sent from the IO-Link devices to the diagnostic telegram of the master.
Event Codes can be read from the connected devices by using appropriate device tools (e.g.
IODD-Interpreter).
Further information concerning the IO-Link Event Codes and their meaning can be found in
the IO-Link specification or in the documentation of the connected devices.

10.4.1

Status- and control word

Status word

EtherNet/IP™
Modbus

PROFINET

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

Byte 0

Byte 1

V2

-

-

-

-

-

ARGEE

DIAG

Byte 1

Byte 0

-

FCE

-

-

-

COM

V1

-

Bit

Description

COM

Internal error
The device-internal communication is disturbed.

DIAG

Diagnostic messages at the device

FCE

The DTM Force Mode is activated, which means, the actual output values may no
match the ones defined and sent by the field bus.

V1

V1 or V2 too low (< 18 V DC).

V2

The status word is mapped into the module's process data.
In EtherNet/IP™ the mapping can be deactivated via the Gateway Class (VSC 100).

NOTE

Activating or deactivating the status and control word modifies the process data
mapping.

Control word

The control word has no function.

«
...
118
119
120
121
122
...
»

Содержание TBEN-S2-4IOL







































































































































Отзывы:

Нет отзывов