manualshive.com logo in svg

turck BL67-GW-PN-AC, Руководство пользователя, Страница: 101 / 119

Поделиться
Скачать
turck BL67-GW-PN-AC Скачать руководство пользователя страница 101

D301239 1013 - BL67 AIDA PROFINET

7-7

Shielding of cables

7.4

Shielding of cables

Shielding is used to prevent interference from voltages and the radiation of interference fields by 
cables. Therefore, use only shielded cables with shielding braids made from good conducting materials 
(copper or aluminum) with a minimum degree of coverage of 80%. 

The cable shield should always be connected to both sides of the respective reference potential (if no 
exception is made, for example, such as high-resistant, symmetrical, analog signal cables). Only then 
can the cable shield attain the best results possible against electrical and magnetic fields.

A one-sided shield connection merely achieves an isolation against electrical fields.

The insulation of the shielded data-cable should be stripped and connected to the shield rail when the 
system is used in stationary operation The connection and securing of the shield should be made using 
metal shield clamps. The shield clamps must enclose the shielding braid and in so doing create a large 
surface contact area. The shield rail must have a low impedance (for example, fixing points of 10 to 20 
cm apart) and be connected to a reference potential area. 

The cable shield should not be severed, but routed further within the system (for example, to the 
switchgear cabinet), right up to the interface connection.

Attention

When installing, please pay attention to the following...

– the shield should be connected immediately when entering the system, 
– the shield connection to the shield rail should be of low impedance,
– the stripped cable-ends are to be kept as short as possible,
– the cable shield is not to be used as a bonding conductor.

If the data cable is connected via a SUB-D connector, the shielding should never be connected 
via pin 1, but to the mass collar of the plug-in connector.

Note

Should it not be possible to ground the shield on both sides due to switching arrangements 
or device specific reasons, then it is possible to route the second cable shield side to the local 
reference potential via a capacitor (short connection distances). If necessary, a varistor or 
resistor can be connected parallel to the capacitor, to prevent disruptive discharges when 
interference pulses occur.

A further possibility is a double-shielded cable (galvanically separated), whereby the 
innermost shield is connected on one side and the outermost shield is connected on both 
sides.

Содержание BL67-GW-PN-AC
























































































































Отзывы:

Нет отзывов