TTControl Vision 312 Скачать руководство пользователя страница 33

Страница: 33 / 45

7. INTERNAL STRUCTURE

7.3.1 Characteristics

Symbol

Parameter

Note

Min

Max

Unit

Δ min/year

Time variation per year at 25

○

-5

min/year

RTC power reserve

days

Note 1

If the super-capacitor has been charged for at least 5 hours with V

BAT+

> 9 V.

7.4 Memory

The Vision 312 device provides the following storage memory types:

• eMMC NAND-flash storage (large and fast memory array)

• EEPROM storage

7.4.1 Characteristics

Memory

Parameter

Note

Typ

Unit

eMMC flash memory available for user data

EEPROM memory available for user data

EEPROM data retention

years

EEPROM erase/write cycles

per byte

1.2*10

cycles

Note 1

Only for Vision 312 products.

Note 2

Only for Vision 312Plus products.

Note 3

At 85

○

Document Number:

D-156-G-02-001

Содержание Vision 312














































Результаты поиска

Содержание Vision 312

Отзывы:

Похожие инструкции для Vision 312

Бренды по названию

Популярные бренды

TTControl Vision 312, Руководство пользователя

Результаты поиска

Содержание Vision 312

Отзывы:

Похожие инструкции для Vision 312

Бренды по названию

Популярные бренды