manualshive.com logo in svg

Tsurumi Pump LSC Series, Руководство по эксплуатации, Страница: 12 / 18

Поделиться
Скачать
Tsurumi Pump LSC Series Скачать руководство пользователя страница 12

-10-

 Before starting

(1) Make sure once again that the product is of the correct voltage and frequency rating.

CAUTION

  Using the product at other than rated voltage and frequency will not only 

lower its performance but may damage the product.

Note:

Confirm the rated voltage and frequency on the model name plate.

(2) Confirm the wiring, supply voltage, circuit breaker capacity, and motor insulation resis-

tance.

 

 

 

 

Reference insulation resistance = 20MΩ or greater.

Note:

 

The reference insulation resistance (20MΩ or greater) is the value when the pump is new 

or has been repaired. For the reference value after installation, see below at Maintenance 

and Inspection (p.11).

 (3) The setting on the circuit breaker or other overload protector should be made in ac-

cord with the rated current of the pump.

Note:

See the model name plate on the pump for its rated current.

 (4) When powering the pump with a generator, do not share the generator with other 

equipment.

Test Operation 

WARNING

  Never Operate the pump while it is suspended in the air. The recoil may result 

in injury or other major accident.

 

Never start the pump when people are standing next to it. An electrical leak 

can result in electrical shock.

(1) •Model LSC

 

The Pump will not start until the pump casing is wet. When 

doing a test operation or if it is desired to start the pump 

when the remaining water level is low, pour in clean water 

from the hose coupling. Approximately 2.5 liter of priming 

water is required.

 

•Model LSP

 

Remove the priming plug at the top of the pump and pour 

in clean water right up to the top: then replace the priming 

plug and tighten it. Approximately 1.8 liter of priming water 

is required.

 (2) Run the pump for a short time (3 to 10 minutes) and check 

its operation.

1.8

Water

Priming Plug

LSP

CAUTION

  In case of very excessive vibration, unusual noise or odor, turn off the power 

immediately and consult with your nearest dealer or Tsurumi representative. 

Continuing to operate the pump under abnormal conditions may result in 

electrical shock, fire, or electrical leakage.

Operation 

WARNING

  The pump may become very hot during operation. Be careful not to contact 

the pump accidentally to avoid being burned.

Always make sure the pump is primed before starting operation.
If the motor protection system operates due to an overload or malfunction, causing the 

pump to stop, first investigate and remove the cause before restarting.
If LSC is used: After stopping operation, detach the hose from the discharge connector and 

turn the pump upside-down to remove the water inside the pump.

6 OPERATION

CAUTION

  Do not run the pump dry or with shut off condition. This condition may 

damage the pump or cause it to malfunction and may result in electrical 

leakage or electrical shock.

Содержание LSC Series



















Отзывы:

Нет отзывов