background image

17200120/B-10083-3

INTRODUCTION

Thank you for selecting the Tsurumi LB Submersible Portable Dewatering Pump for your 
application.
This equipment should not be used for applications other than those listed in this manual. 
Failure to observe this precaution may lead to a malfunction or an accident. In the event of 
a malfunction or an accident, the manufacturer will not assume any liability. After reading 
this Operation Manual, keep it in a location that is easily accessible, so that it can be re-
ferred to whenever information is needed while operating the equipment.

OPERATION MANUAL

LB

    Submersible Portable Dewatering Pump

 

 

LB-1500

 

 

LBT-1500

CONTENTS

1. BE SURE TO READ FOR YOUR SAFETY .....................1
2. PART NAMES .................................................................4
3. PRIOR TO OPERATION   ...............................................4
4. INSTALLATION   .............................................................5
5. ELECTRICAL WIRING ....................................................7
6. OPERATION ....................................................................9
7. MAINTENANCE AND INSPECTION ...............................11
8. DISASSEMBLY AND REASSEMBLY PROCEDURE ...... 13
9.TROUBLESHOOTING   ...................................................15

TSURUMI MANUFACTURING CO., LTD.

Содержание LB-250

































Отзывы: