TSUJI ELECTRONICS PM16C-16HW2 Скачать руководство пользователя страница 54

Страница: 54 / 75

<ch>: 0 ~ F(Hexadecimal) for channel.

7-7 Setting of the local mode data

Command SHPF<ch><off>

Set the home position offset.
When you detect home position by command "GTHPx", home
position searching starts from the distance of offset value from
current home position.

Argument <off>

offset

0 ~ 99,999

Initial value 100

Reply Nothing

Example SHPF51000 Set 1,000 to the offset of CH5.

Remarks Only remote mode.

Command SHPF?<ch>

Confirm the home position offset.

Reply dddd (4-digit)

Example SHPF?5 replty: 0100

Remarks

Command S<mode><ch><pos>

Set the various values to be used in local mode.

Argument

<mode>

Mode

REL/ Value of the relative movement by START button in

REL mode.

ABS/ Value of the absolute movement by START button in

ABS mode.

PRS/ Value to be set by PRESET button in SCAN mode.

<pos>

Set posotion

-2,147,483,647 ~ +2,147,483,647

Initial value REL: +10000 ABS: 0 PRS: 0

Reply Nothing

Example

SPRSB+10000 Set +10000 to the preset value of CH11 for when PRESET button will

be pressed.

Remarks Only remote mode.

Command S<mode>?<ch>

Confirm the various values to be used in local mode.

Argument <mode>

Mode

REL/ Value of the relative movement by START button in REL

mode.

ABS/ Value of the absolute movement by START button in

ABS mode.

PRS/ Value to be set by PRESET button in SCAN mode.

ddddddd (Signed integer 7 digits or more)

Example

SPRS?1 reply: +0002500
Preset value is +2500, when PRESET button on the CH1 is pressed.

Remarks

Содержание PM16C-16HW2












































































Результаты поиска

Содержание PM16C-16HW2

Отзывы:

Похожие инструкции для PM16C-16HW2

Бренды по названию

Популярные бренды

TSUJI ELECTRONICS PM16C-16HW2, Руководство пользователя

Результаты поиска

Содержание PM16C-16HW2

Отзывы:

Похожие инструкции для PM16C-16HW2

Бренды по названию

Популярные бренды