TSUJI ELECTRONICS PM16C-16HW2 Скачать руководство пользователя страница 50

Страница: 50 / 75

7 Commands for parameter set up

<ch>: 0 ~ F(Hexadecimal) for channel.

7-3 Acceleration and deceleration Rate Setting

Command SPDAL?

Display the speed that has been set to the motor that displays in LCD.

<0123>/<sp>dddddd/<sp>dddddd/<sp>dddddd/<sp>dddddd

<0123>

Expressed in hexadecimal notation of four-digit channel which is
displayed on the display. Display the following parameters in this order.

<sp>

H/HSPD M/MSPD L/LSPD
Display the speed that has been set to the motor.

dddddd

Display the speed as pps.

Example SPDAL? Reoky: 0123/M000650/H010000/L000100/M000650

Remarks

If the motor is in operation, display of dddddd part appears in 000000.

Command RTE<ch><cd>

Set the code in the acceleration and deceleration rate.

Argument <cd>

acceleration and
deceleration code

Enter the code a number between 0 - 115.
Refer to page 48 about the relationship of acceleration
and deceleration of the actual code.

Initial value 013

Reply Nothing

Example RTE040 Set to 40 for the acceleration and deceleration rate of CH0.

Remarks Only remote mode. And the motor is stopped.

Command RTE?<ch>

Confirm the code in the acceleration and deceleration rate.

Reply DDD (

3-digit integer

)

Example RTE?0 reply: 050 The acceleration and deceleration rate of CH0 is 50.

Remarks

Command RRATE<ch><rrt>

Set the acceleration / deceleration rate as a real number.

Argument <rrt>

Rate value

1000~0.00125

Initial value 300.000

Reply none

Example RTE02.5 Set the acceleration / deceleration rate of channel 0 to 2.5ms / 1000pps.

Remarks Valid only when the motor is stopped and when remote, see the next page for details.

Command RRATE?<ch>

Check the acceleration / deceleration rate with a real number.

Reply DDD .ddd (real number with 3 decimal places)

Example

RRATE? 0 reply: 2.500
The acceleration / deceleration rate for channel 0 is 2.5ms / 1000 pps .

Remarks

Содержание PM16C-16HW2












































































Результаты поиска

Содержание PM16C-16HW2

Отзывы:

Похожие инструкции для PM16C-16HW2

Бренды по названию

Популярные бренды

TSUJI ELECTRONICS PM16C-16HW2, Руководство пользователя

Результаты поиска

Содержание PM16C-16HW2

Отзывы:

Похожие инструкции для PM16C-16HW2

Бренды по названию

Популярные бренды