TSI Instruments DustTrak 8535 Скачать руководство пользователя | Manualshive

Страница: 57 / 70

background image

47

Chapter 4

Maintenance

Daily Maintenance Checks

Check the DustTrak

™ II/DRX aerosol monitor a minimum of once a

day to change the battery pack(s) and make sure that the instrument
is operating properly. A visual inspection of the instrument and case
can ensure that the water trap is empty, the sampling inlet is
unobstructed and the tubing is not kinked.

Cleaning the Aerosol Inlet

Under normal operating conditions, the external aerosol inlet will
remain clean and unobstructed. Under very dirty conditions; however,
the inlet may become obstructed with vegetative debris or insects. To
ensure the inside of the aerosol inlet is clean, periodically blow
compressed air through the bottom of the inlet.

C A U T I O N

DO NOT

disassemble the Environmental Enclosure

aerosol inlet for any reason. It is

NOT

designed for

field service and reassembly.

Cleaning the Respirable Aerosol Inlet

Follow the same procedure found in the DustTrak

™ II or

DustTrak

™ DRX Aerosol Monitor user manual.

When to Change the Battery

Single battery packs are designed to provide power to the
DustTrak

™ II/DRX monitor for a minimum of 34 hours, even under

cold ambient conditions. However, if using the DustTra

k™ II/DRX

monitor with External, single battery packs will provide power for a
minimum of 23 hours.

If using the Dual Battery Wiring Harness, two battery packs will
provide power to the DustTrak

™ II/DRX monitor for roughly 65 hours

or two battery packs will provide power to the DustTra

k™ II/DRX

monitor with External Pump for at least 42 hours. To ensure
uninterrupted operation, the packs should be replaced daily or within
the time period listed above.

«
...
55
56
57
58
59
...
»

Содержание DustTrak 8535







































































Отзывы:

Нет отзывов

Похожие инструкции для DustTrak 8535

Бренд: Campbell Страницы: 48

Бренд: ZALMAN Страницы: 7

GAMING VIRTUS NEO WHITE

Бренд: 2E Страницы: 30

Бренд: SilverStone Страницы: 48

EPIC By-Pass Sliding Doors

Бренд: GlassCrafters Страницы: 13

Бренд: Rosewill Страницы: 12

Бренд: COUGAR Страницы: 2

Бренд: SilverStone Страницы: 16

Бренд: StarTech.com Страницы: 11

Бренд: Swarovski Optik Страницы: 2

Бренд: Lazer3D Страницы: 28

Бренд: Vantec Страницы: 23

Бренд: Vantec Страницы: 23

Бренд: Interactive Страницы: 6

Бренд: Minebea Intec Страницы: 24

Бренд: Eurotech Страницы: 25

Бренд: QNAP Страницы: 37

Бренд: TOOQ Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды