TSI Instruments AEROTRAK 9306 Скачать руководство пользователя страница 27

Страница: 27 / 82

Operation

3-5

Field

Description

(

Zone

)

Displays the Zone where the sample is being
taken by the instrument. Press the icon to display
a summary of information for the Zone.

(

Location

)

This drop-down box allows selection of a
preconfigured Location to associate the sampled
data to.

Time

The time for each sample.

Delay

The Delay displays one of two times:

1. Before the

Start

button is pressed the

Start

Delay

time is displayed and then

immediately after the

Start

button is

pressed the Delay time begins a countdown.

2. During sampling and between cycles (after

the

Start Delay

has been displayed), the

Hold Delay

is displayed and then begins a

countdown.

Recs

The total number of records in the
database/10000 (maximum number of records).

Manual/Automatic/Beep

Mode Indicator; refers to the “

Data Count Mode

”

(see section below).

Start/Stop

button to begin and end sampling in

the configured mode.

Start/Stop

may also be

entered using the triangle-shaped button above
the power button on the front of the instrument.

Press to print the current sample to the
optional printer.

Содержание AEROTRAK 9306



















































































Результаты поиска

Содержание AEROTRAK 9306

Отзывы:

Бренды по названию

Популярные бренды

TSI Instruments AEROTRAK 9306, Руководство по эксплуатации

Результаты поиска

Содержание AEROTRAK 9306

Отзывы:

Бренды по названию

Популярные бренды