TSE PTV100/72, Руководство пользователя

Страница: 82 / 480

Fuels, Lubricants, and Coolants
DX,ENOIL16 -19-15JUN10-1/1
DX,ENOIL14 -19-15JUN10-1/1
John Deere Break-In Plus™ Engine Oil — Interim Tier 4, Final Tier 4, Stage IIIB, and Stage IV
New engines are filled at the factory with John Deere
Break-In Plus™ Engine Oil. During the break-in period,
add John Deere Break-In Plus™ Engine Oil, as needed to
maintain the specified oil level.
Operate the engine under various conditions, particularly
heavy loads with minimal idling, to help seat engine
components properly.
During the initial operation of a new or rebuilt engine,
change the oil and filter between a minimum of 100 hours
and maximum equal to the interval specified for John
Deere Plus-50™ II oil.
After engine overhaul, fill the engine with John Deere
Break-In Plus™ Engine Oil.
If John Deere Break-In Plus™ Engine Oil is not available,
use an SAE 10W-30 viscosity grade diesel engine oil
meeting one of the following:
•
API Service Category CJ-4
•
ACEA Oil Sequence E9
•
ACEA Oil Sequence E6
If one of these oils is used during the initial operation of a
new or rebuilt engine, change the oil and filter between a
minimum of 100 hours and a maximum of 250 hours.
IMPORTANT: Do not use any other engine oils during
the initial break-in of a new or rebuilt engine.
John Deere Break-In Plus™ Engine Oil can be used for
all John Deere diesel engines at all emission certification
levels.
After the break-in period, use John Deere Plus-50™ II or
other diesel engine oil as recommended in this manual.
Break-In Plus is a trademark of Deere & Company
Plus-50 is a trademark of Deere & Company.
Diesel Engine Oil — Interim Tier 4, Final Tier 4, Stage IIIB, and Stage IV
Use oil viscosity based on the expected air temperature
range during the period between oil changes.
John Deere Plus-50™ II is the recommended
engine oil.
Extended service intervals may apply when John Deere
Plus-50™ II engine oil is used. Refer to the engine oil
drain interval table and consult your John Deere dealer
for more information.
If John Deere Plus-50™ II engine oil is not available,
engine oil meeting one or more of the following may be
used:
•
API Service Category CJ-4
•
ACEA Oil Sequence E9
•
ACEA Oil Sequence E6
DO NOT use engine oil containing more than 1.0%
sulfated ash, 0.12% phosphorus, or 0.4% sulfur.
Multi-viscosity diesel engine oils are preferred.
Diesel fuel quality and fuel sulfur content must comply
with all existing emissions regulations for the area in
which the engine operates.
IMPORTANT: Use only ultra low sulfur diesel
(ULSD) fuel with a maximum sulfur content
of 15 mg/kg (15 ppm).
SAE 15W
-40
SAE 10W
-40
SAE 10W
-30
SAE 0W
-40
SAE 5W
-30
50 C
o
40 C
o
30 C
o
20 C
o
10 C
o
0 C
o
-10 C
o
-20 C
o
-30 C
o
-40 C
o
122 F
o
50 F
o
32 F
o
14 F
o
-4 F
o
-22 F
o
-40 F
o
104 F
o
68 F
o
86 F
o
TS1691
—UN—18JUL07
Oil Viscosities for Air Temperature Ranges
Plus-50 is a trademark of Deere & Company
10-9 032015
PN=40