Tryton TCV14L2, Руководство по эксплуатации

Страница: 6 / 52

PREPARATION FOR WORK: Gear I: Used for driving and unscrewing screws.
Gear II: Used for drilling.
CAUTION: Do not change the position of the gear shifter ( 3 ) during tool
operation as this may damage the gear box. Always allow the tool to come
to a full stop before changing the setting of the gear shifter.
If the gear shifter does not move all the way, move the drive spindle
slightly.
1. Disconnect the battery ( 7 ) from the driver.
2. Open the chuck as much as possible ( 1 )
3. Using a PH 2 (Philips No.2) screwdriver, rotate the fixing screw ( 16 ) of
the chuck clockwise ( CAUTION! L eft-thread ).
4. Hold the lower chuck ring (the one closer to the driver body) and
rotate the drill/driver chuck counter-clockwise (looking from the
point of view of the chuck).
CAUTION: A jammed keyless chuck ( 1 ) can be released by inserting the
short end of a hex key in the chuck and lightly tapping the longer arm of
the key (see Fig.
D ).
5. To attach the chuck, screw it onto the drive spindle counter-clockwise
(looking from the chuck side) and secure by screwing in the fixing
screw counter-clockwise using a PH 2 screwdriver (No.2 Philips). For
the chuck not to rotate during screwing in the fixing screw, the chuck
should be held by the lower ring (the one closer to the drill/driver
body).
Both sides of the drill/driver body have in-built inserts ( 8 ), which
make it possible to hold bits during work.
The drill/driver is equipped with an auxiliary light (
1 1 ) for the area of
drilling/driving, which turns on after the appropriate switch ( 1 0 ) is
pushed.
CAUTION: Disconnect the battery from the driver or put the rotation
direction switch ( 4 ) in the middle position to secure the machine from being
started by mistake, which could in turn cause harm to the user.
1.
The gear shifter ( 3 ) makes it possible to choose 2 rotation speed ranges.
n
Charging the battery
The driver is supplied with a partially charged battery. Charge the battery
fully before use. It is recommended that the first charging session lasts at
least 1 hour.
Press the battery lock button (
9 ), slide the battery out ( 7 ) (Fig. B ) and
insert into charger socket ( 1 3 )(Fig. C ). Connect charger to an electrical
socket 100-240 V, 50Hz.
n
Battery charging indicator
A green LED light indicates that the charger is connected to a power
source.
A
red light flashing with a frequency of about 1/s (1Hz) indicates that
charging is in progress.
Once the battery is fully charged, the red light stops flashing and both,
red and green, lights are lit continuously.
The charging current is lowered automatically as charging progresses.
After approx. 1 hour the charging current is stabilised at a minimum level
(trickle charging), which prevents battery overcharging and damage.
After charging, disconnect the charger and remove the battery.
The lithium-ion battery can be charged at any moment, without
detriment to its life. Interrupting the charging process does not entail a
risk of damaging the battery cells.
IN USE:
n
Turning on/off
The switch ( 1 0 ) has fluid rotation speed adjustment built-in.
Auxiliary components
Press the switch to activate the power tool. The rotation speed will
increase the further the switch is pushed. To stop the power tool, release
the switch.
n
Choosing rotation direction (Fig. E )
The driver can work with clockwise (right) or counter-clockwise (left)
rotation.
I nstallation and removing drills to/from the keyless chuck
- to select clockwise rotation, move the clockwise/counter-clockwise
slider (
4 ) to the right (looking from the back of the driver),
- to select counter-clockwise rotation, move the clockwise/counter-
clockwise slider (
4 ) to the left (looking from the back of the driver),
When the tool switch ( 10 ) is released the drill chuck is locked. It enables
When the rotation direction switch is in the middle position, it is locked.
quick, easy and convenient replacement of a working tool installed in the
For drilling and driving screws in, clockwise operation should be
drill chuck. To remove a drill (or a working bit) from the drill chuck, rotate
selected. For taking out the drill bit, removing a stuck drill bit, or
the chuck ring anticlockwise to expand the opening of the chuck. Insert a
unscrewing screws, counter-clockwise operation should be selected.
new drill (or a working bit) into the chuck and rotate the chuck ring
n
Choosing torque (Fig. F )
clockwise to secure the drill in the drill chuck.
The driver is equipped with a ring ( 2 ), which can be used for setting the
Drills (or other working bits) must be moved to the full depth of the chuck
toque when driving screws. The ring has 22 settings, from 1 to 21 , and a
opening.
drilling setting.
Drilling boreholes
Using a given setting (from 1 - 21 ) means that the clutch is set to an
To drill deep boreholes carry out your job gradually, drill to lower
assigned toque. This makes it possible to prevent a screw from being
depths and remove the drill from the borehole from time to time to
driven too far or being damaged. Different torques should be used for
remove borings from the borehole.
different screws and materials.
To drill large diameter boreholes it is recommended to start with
Always start with a low torque and increase gradually until the desired
drilling a low-diameter borehole and then expand it to the desired
result is achieved.
diameter. It prevents the tool from overloads.
For drilling in metal, wood or plastic, set the ring ( 2 ), so that the indicator
When the drilling bit is seized during working switch immediately the
( 1 4 ) points to symbol ( 1 5 ) .
tool off to prevent it from being damaged. Switch the rotations
direction to the anticlockwise rotations and then remove the drilling
bit from the borehole.
n
Changing the chuck (Fig. G )
To free a seized bolt
hit is gently on its head.
n
ź
ź
n
n
2.
3.
n
Shifting gear (Fig. A1 )
6