background image

3

SICI-7-1/4N4

11779

7-1/4”

Clase II

60 Hz

Circular Saw

14 AWG X 2C with 194 °F insulation temperature.

50 minutes’ work per 20 minutes’ rest.

Maximum 6 hours daily.

14 A

1 800 W

Code

Description

Disc

Voltage

Frequency

Current

Power

6000 RPM

Speed

Work Cycle

Conductors

Insulation

IP20

IP Grade

Power Cord Grips used in this product: Type “Y”.

Tool Build Quality: Reinforced insulation

Thermal insulation on motor winding: Class F

127 V

ENGLISH

Power Requirements

WARNING

WARNING

Avoid the risk of electric shock or severe injury. When the power cable gets damaged 

it should only be replaced by the manufacturer or at a                                 Authorized Service Center.

The build quality of the electric insulation is altered if spills or liquid gets into the tool while in use.

Do not expose to rain, liquids and/or dampness.

Before gaining access to the terminals all power sources should be disconnected.

Technical Data

Tools with double insulation and reinforced insulation are 

equipped with a polarized plug (one prong is wider than the other). This plug will 

only fit in the right way into a polarized outlet. If the plug cannot be introduced into 

the outlet, reverse the plug. If it still doesn’t fit, call a qualified electrician to install 

for you a polarized outlet. Do not alter the plug in any way. Both insulation types 

eliminate the need of both a grounded third power cord with three prongs or a 

grounded power connection.

When using an extension cable, verify the gauge is enough for 

the power that your product needs. A lower gauge cable will cause voltage drop in the line, resulting in power loss and 

overheating. The following table shows the right size to use depending on cable’s length and the ampere capability shown in 

the tool’s nameplate. When in doubt use the next higher gauge.

WARNING

WARNING

from 0 A and up to 10 A

from 10 A and up to 13 A

from 13 A and up to 15 A

from 15 A and up to 20 A

18 AWG(*)

16 AWG

14 AWG

8 AWG

16 AWG

14 AWG

12 AWG

6 AWG

3 (one grounded)

from 6’ to 49’        |         higher than 49’

Ampere

Capacity

Number of

Conductors

Extension gauge

* It is safe to use only if the extensions have a built-in artifact for over current protection.

AWG = American Wire Gauge. Reference: NMX-J-195-ANCE

WARNING

When operating power tools outdoors, use a                       grounded 

extension cable labeled “For Outdoors Use”. These extensions are specially designed for 

operating outdoors and reduce the risk of electric shock.

Содержание 11779

























Отзывы: