background image

3

• IMPORTANT SAFETY INSTRUCTIONS •

READ ALL INSTRUCTIONS BEFORE OPERATING 

• Read the instructions carefully. Be familiar with the controls and 

proper use of the unit. Know how to stop the unit and disengage 

the controls quickly. 

• Stay alert. Do not operate this unit when tired, ill or under the 

influence of alcohol, drugs or medication. 

• Never allow children to operate the unit. Teens must be trained, 

accompanied and supervised by an adult. Never allow adults to 

operate the unit without proper instruction.  

• All guards and safety attachments must be installed properly 

before operating the unit. 

• Inspect the unit before use. Check for damaged parts. Check for 

fuel leaks. Make sure all parts operate properly. Make sure all 

fasteners are in place and secure. Make sure all moving parts are 

properly aligned and are not bound. Replace parts that are cracked, 

chipped, or damaged in any way. Have all damaged or improperly 

working parts repaired or replaced by an authorized service center. 

Do not operate the unit with loose or damaged parts.  

• Be aware of risk of injury to the head, hands and feet. 
• Carefully inspect the area before starting the unit. Remove 

rocks, broken glass, nails, wire, string and other objects that 

may be thrown or become entangled with the unit.  

• Clear the area of children, bystanders and pets; keep them 

outside a 50-foot (15 m) radius, at a minimum. Even then, they are 

still at risk from thrown objects. Encourage bystanders to wear 

eye protection. If you are approached, stop the unit immediately. 

• Squeeze the throttle control and check that it returns 

automatically to the idle position. Make all adjustments or 

repairs before using the unit. 

• Do not change the engine governor settings or overspeed the 

engine. 

• This unit is intended for occasional, household use only.

WARNING:

 When using the unit, all safety 

instructions must be followed. Please read these 

instructions before operating the unit in order to ensure the 

safety of the operator and any bystanders. Please keep 

these instructions for later use.

SAFETY WARNINGS FOR GAS UNITS 

• Store fuel only in containers specifically designed and approved 

for the storage of such materials. 

• Always stop the engine and allow it to cool before filling the 

tank. Never remove the fuel tank cap or add fuel when the 

engine is hot. Always loosen the fuel tank cap slowly to relieve 

any pressure in the tank before fueling. 

• Always mix and add fuel in a clean, well-ventilated outdoor area 

where there are no sparks or flames. DO NOT smoke. 

• Never operate the unit without the fuel cap securely in place. 
• Avoid creating a source of ignition for spilled fuel. Wipe up any 

spilled fuel from the unit immediately, before starting the unit. 

Move the unit at least 30 ft. (9.1 m) from the fueling source and 

site before starting the engine. DO NOT smoke. 

• Never start or run the unit inside a closed room or building. 

Breathing exhaust fumes can kill. Operate this unit only in a well 

ventilated outdoor area.

WARNING:

 Gasoline is highly flammable and 

its vapors can explode if ignited. Take the following 

precautions:

WHILE OPERATING 

• Wear safety glasses or goggles that meet current ANSI / ISEA 

Z87.1 standards and are marked as such. Wear ear/hearing 

protection when operating this unit. Wear a face mask or dust 

mask if the operation is dusty. Use a hard hat or other type of 

safety helmet. 

• Wear heavy long pants, boots, gloves and a long sleeve shirt. Do 

not wear loose clothing, jewelry, short pants, sandals or go 

barefoot. Secure hair above shoulder level. 

• The cutting head / blade should remain stationary when the 

engine idles. If it does not, refer to Adjusting the Idle Speed

• Adjust the handle to provide the best grip, if applicable. 
• Make sure the cutting head / blade is not in contact with 

anything before starting the unit. 

• Use the unit only in daylight or good artificial light. 
• Avoid accidental starting. Be in the starting position whenever 

pulling the starter rope. The operator and unit must be in a 

stable position while starting. Refer to Starting and Stopping

• Use the right tool. Only use this tool for its intended purpose. 

Only use the unit as described in this manual. 

• Always hold the unit with both hands when operating. Keep a 

firm grip on both handles or grips. 

• Do not overreach. Always keep proper footing and balance. Take 

extra care when working on stairs, steep slopes or inclines. To 

avoid serious injury, do not operate the unit while on a ladder or 

a roof. 

• Keep hands, face, and feet away from all moving parts. Do not 

touch or try to stop moving parts. 

• Do not touch the engine, gear housing or muffler. These parts get 

extremely hot from operation, even after the unit is turned off. 

• Do not operate the unit faster than the speed needed to do the 

job. Do not run the unit at high speed when not in use. 

• Do not force the unit. It will do a better, safer job when used at 

the intended rate. 

• Always turn the unit off when operation is delayed or when 

carrying the unit from one location to another. Make sure all 

moving parts come to a complete stop. 

Содержание TB27 BC

















































Отзывы: