Troy-Bilt 68J-Horse, Руководство оператора

Страница: 39 / 64

Tine Shaft Maintenance
After every 10 operating hours, remove
the left- and right-side Bolo Tine holders
and clear away dirt and debris that have
accumulated on the tine shaft or inside
the tine holders. Please follow this main-
tenance recommendation, as debris can
cause premature wear to the tine shaft
and its oil seals. Refer to the previous
tine holder removal instructions. After
cleaning away any debris and removing
old grease from the tine shaft, apply fresh
grease to the tine shaft.
Tire and Wheel Maintenance
Check tire air pressure every 30 operating
hours. The recommended pressure for
tilling is 10-to-20 psi (pounds per square
inch). Both tires should be inflated
equally. (Unequal pressure can cause the
tiller to pull to one side.)
Removing the Wheels
Each wheel is secured by a roll (spirol)
pin that passes through the wheel hub
and the wheel shaft. Drive the roll pin out
to remove a wheel.
1. Prop the transmission up with a sturdy
block to raise the wheel you want to
remove off the ground.
2. Move the Wheel Speed Lever to either
SLOW or FAST position to prevent the
wheels from turning.
3. Use a 5/16" drift pin (or a blunt point
16-penny nail) to drive the roll pin free.
Engine Oil Maintenance
Check the engine oil level before starting
the engine each day and after each 5
hours of continuous operation. Running
the engine when it is low on oil will
quickly ruin the engine.
It is recommended that you change the oil
every ten (10) operating hours and even
sooner when operating in extremely dirty
or dusty conditions. Refer to the separate
Engine Owner’s Manual for detailed
service instructions.
Air Cleaner Maintenance
The engine is equipped with a dual
element air cleaner that filters the air
twice before it enters the carburetor to
mix with the fuel.
The engine air cleaner filters dirt and dust
out of the air before it enters the carbure-
tor. Operating the engine with a dirty,
clogged air filter can cause poor perfor-
mance and damage to the engine. Never
operate the engine without the air cleaner
installed. Inspect and service the air
cleaner more often if operating in very
dusty or dirty conditions.
It is critical that the filters be kept clean
and properly installed at all times. See
the location of the air cleaner assembly on
your engine by referring to Figure 5-39 or
Figure 5-40.
Refer to the engine manufacturer’s litera-
ture supplied with your tiller for complete
air cleaner service and maintenance infor-
mation.
Throttle Cable Maintenance
The throttle lever settings are factory-
adjusted, so unnecessary adjustments
should not be made. However, if the
engine does not start or stop, or respond
immediately to various throttle lever
settings, then adjustments may be
necessary. Please refer to the engine
manufacturer literature supplied with your
tiller for specific adjustment instructions.
Ignition System Maintenance
Your engine is equipped with electronic
ignition. It does not have a condenser or
points, so there is no need to perform any
regular tune-up maintenance on this
system other than adjusting or replacing
the spark plug.
Spark Plug Maintenance
The spark plug must be in good condition
for proper engine operation. Remove and
inspect the plug every 50 operating hours
or annually, whichever occurs first.
The correct electrode gap is .030". Check
the gap with a feeler gauge. Do not use a
spark plug if the porcelain is cracked, the
electrodes are pitted or burned, or if other
visible damage is present.
NOTE: Do not wire brush or sandblast the
spark plug to clean it – loose particles
can enter the engine, causing damage!
To replace the plug, first tighten it
securely by hand, then use a spark plug
wrench to tighten the plug an extra 1/4
turn.
Battery Care and Maintenance
The battery is sealed and is maintenence-
free. Acid levels cannot be checked.
• Always keep the battery cables and
terminals clean and free of corrosive
build-up.
• After cleaning the battery and
terminals, apply a light coat of
petroleum jelly or grease to the
terminals and cover both terminals
with the rubber boots.
Section 5: Maintenance
Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come
to a complete stop, disconnect spark plug wire and move wire away from spark plug. Remove ignition
key, if so equipped.
Failure to follow these instructions can result in serious personal injury or property damage.
WARNING
Wear safety goggles when driving the
roll pin into or from the wheel hub to
protect your eyes from the possibility of
flying metal particles.
WARNING
39
When removing the battery, always dis-
connect the negative (-) cable first
followed by the positive (+) cable. Re-
verse this procedure when reinstalling
the battery.
WARNING