background image

10.3  Inspection, maintenance and repair measures

Interval Maintenance work

Personnel

A

Access to the fire damper

Internal and external accessibility

Provide access

Specialist personnel

Installation of the fire damper

 

Ä

 Chapter 5   ‘Installation’ on page  12

Installation into walls according to this manual

Install the fire damper correctly.

Specialist personnel

Transport and installation protection, if any

Transport/installation protection removed

Remove transport/installation protection

Specialist personnel

Connection of ductwork/cover grille/flexible connector

Connection according to this manual

Establish correct connection

Specialist personnel

Power supply to the spring return actuator

Power supply according to spring return actuator rating plate

Provide correct power supply

Skilled qualified electrician

A / B

Check fire damper for damage

Fire damper, damper blade and seal must be intact

Replace the damper blade

Repair or replace the fire damper.

Specialist personnel

Function of the release mechanism

Function OK

Fusible link intact/no corrosion

Replace the fusible link

Replace the release mechanism

Specialist personnel

Functional test of the fire damper (with spring return actuator) 

Ä

   18

Actuator function OK

Damper blade closes

Damper blade opens

Determine and eliminate the cause of the fault

Replace the spring return actuator

Repair or replace the fire damper

Specialist personnel

Function of external smoke detector

Function OK

Fire damper closes when triggered manually or when smoke is

detected

Fire damper opens after reset

Determine and eliminate the cause of the fault

Repair or replace smoke detector

Specialist personnel

C

Cleaning the fire damper

No contamination in the interior or on the exterior of the fire damper

No corrosion

Remove contamination with a damp cloth

Remove corrosion or replace part

Specialist personnel

Maintenance

Inspection, maintenance and repair measures  

 

Tunnel fire damper Type FKT-EU

22

Содержание FKT-EU





























Отзывы: