Trotec 1110000120 Скачать руководство пользователя страница 8

8

EN

desiccant dehumidifier TTR 160 / TTR 250

Operation

Control panel

16

15

20

19

17

No.

Designation

Meaning

15

Connection cable

16

Operating hours
counter

Indication of operating hours

17

Mains switch

Switching the device on and off

18

Socket for
external hygrostat

Connection for hygrostat operation

19

Ammeter

Indication of electric current

Switch-on

Switch the device on by actuating the mains switch (17). The
integrated indicator light lights up.

Switch-off

Switch the device off by actuating the mains switch (17). The
integrated indicator light goes off.

Remote operation

Switch the device on by actuating the mains switch (17). The
integrated indicator light lights up.
Connect an external switch or external switching device, e.g. a
hygrostat or timer, to the socket (18) with the suitable Tuchel
plug (optional accessory). Always observe the information
contained in the circuit diagram (see Technical annex).
All electrical loads are now switched on or off by the external
switch as needed. The indicator light of the mains switch
remains illuminated regardless of the switching state and
indicates that the control unit is activate. In hygrostat operation,
air circulation may in some cases be necessary at the point of
moisture measurement. In this case, the fan can be configured
for permanent operation by replugging a plug contact at the
integrated relay. This operation may only be carried out by an
electrically skilled person. If required, please contact the Trotec
customer service.

Errors and faults

Error

Diagnosis

Potential
cause

Remedy

No dehumidi-
fication

Dry air shows
no
temperature
increase

Rotor drive 
defective

Check rotor
drive 
and have it
repaired if
necessary

Ammeter
indicates
strongly
deviating
values

Heating
defective

Renew heating

Ammeter
indicates
deviating
values

Regeneration
air current is
insufficient

Check for free
air flow, check
fan, clean or
renew air filter

Service and repair

Warning

Risk of death due to improper repair!
Never try to make any modifications or repairs on the
device. Unauthorised modifications can lead to serious
injuries or death. Have a certified specialist workshop
perform the repair work.
Repair work may only be carried out by trained
specialist staff!

In case of a technical problem please try to rule out handling or
application errors before contacting our customer service.
For further questions regarding the function and operation of the
dehumidifier as well as for more information in the case of an
error or else for warranty issues we are of course always happy
to be of service.
Please contact:
Trotec GmbH
Grebbener Straße 7
D-52525 Heinsberg
Tel.: +49 (0) 2452 / 962-400
Fax.: +49 (0) 2452 / 962-200
E-mail: [email protected]
www.trotec.de

Содержание 1110000120



















Отзывы: