background image

Plug In

Connectors

Light

Socket

Fixture

Screws for

Light Socket 

(4)

1. LIGHT/COVER INSTALLATION

Align three holes in light grill with
three holes in motor assembly.

Lower light grill into position.

Secure light grill to motor assembly
using three (3) screws for light cover.

1C. Installing the Light Grill

Align

Key Holes

Rotate

Light

Pan

Install Screw

and tighten

1B. Installing the Light Fixture

Install the bulb
into the socket. 

Plug in wire connectors, matching wire colors.

Secure light socket fixture to motor assembly
using four (4) screws for light socket fixture.

Install Bulb

Note: Four screws are pre-installed on Light Pan for light

socket fixture installation. You will need to remove these screws.

Screws for

Light Grill (3)

Lower

Light Grill

Align Holes

After feeding the light wires through the center hole, lower 
the Light Pan onto motor assembly aligning the two loosened
screws with the large end of the key holes.

Rotate Light Pan slightly so that screws are engaged in narrow
end of key holes.

Install the screw remove earlier and tighten all three screws.

Note: Three screws are pre-installed on motor assembly for light

pan installation. You will need to remove one and loosen two of

these screws.

1A. Installing the Light Pan

Hint: Lay the motor assembly on the styrofoam packing with the light wires up,

Содержание 59DFG-L







Отзывы: