background image

Maintenance and Adjustment

75

Engine Oil

 Warning

Motorcycle operation with insufficient, 

deteriorated, or contaminated engine 

oil will cause accelerated engine 

wear and may result in engine or 

transmission seizure.
Seizure of the engine or transmission 

may lead to sudden loss of control and 

an accident.

In order for the engine, transmission, 

and clutch to function correctly, 

maintain the engine oil at the correct 

level, and change the engine oil and 

oil filter in accordance with scheduled 

maintenance requirements.

Engine Oil Level Inspection

 Warning

Never start the engine or run the 

engine in a confined area.
Exhaust fumes are poisonous and can 

cause loss of consciousness and death 

within a short period of time.
Always operate the motorcycle in the 

open air or in an area with adequate 

ventilation.

 Warning

If the engine has recently been 

running, the exhaust system will be 

hot.
Before working on or near the exhaust 

system, allow sufficient time for the 

exhaust system to cool as touching 

any part of a hot exhaust system 

could cause burn injuries.

 Caution

Running the engine with insufficient 

oil will cause engine damage.
If the low oil pressure indicator 

remains on, stop the engine 

immediately and investigate the 

situation.

3
4

citl

2

1

1.  Filler plug
2.  Sight glass
3.  Maximum limit
4.  Minimum limit

Содержание Thruxton TFC 2019



































































































































Отзывы: