Triton T12ID, Инструкция по эксплуатации и безопасности

Страница: 7 / 84

7
GB
Battery Charging Table
Red LED Green LED
Battery Charger plugged In OFF Flashing
Charger evaluating Battery OFF Flashing
Fast charging ON OFF
Highly discharged battery slow charging Flashing OFF
Abnormal battery temperature charging Flashing OFF
Fully charged OFF ON
Battery or charger fault Flashing Flashing
Temporary abnormal temperature
condition ON On
Note: If the lights on the Battery Charger fail to illuminate according to the chart above or
indicate a fault condition:
• Check the Battery is firmly seated in the Battery Charger
• Check all connections and that mains power is switched on
Initial charge
• The initial charge will vary depending on the existing charge in the Battery. Allow the
Battery to reach full charge as indicated on the Battery Charger
• After discharging, recharge the Battery completely, as indicated by the LED on the Battery
Charger, for the next 4 to 5 uses. This will ensure that the Battery is performing to its
highest capacity
• Subsequent full charges will take approximately 1 hour, however the Battery can be
recharged when the Battery is only partially discharged
Re-charging the battery
• After use, a lithium-ion battery must be allowed to cool down before charging
• If a hot battery is inserted into the charger both LEDs will illuminate. The charger will begin
to charge when the battery has cooled sufficiently (this may take several minutes)
Installing the battery
• The Battery should fit easily into the Battery Charger or impact driver unit. If the Battery is
difficult to fit, check the condition of the Battery and contacts
Battery - length of service
The length of service from each charging cycle will depend on the type of workload. The
battery charger and battery for this tool have been designed to provide a long trouble-free
working life. The charger intelligently monitors the condition of the battery and selects the
ideal charging rate for the condition of the battery. It protects the battery from over-charging or
charging at too high a rate. However, like all batteries, performance will be reduced over time.
To maximise battery life:
• Store and charge the battery in a cool area. Temperatures above or below normal room
temperature will reduce battery life
• Never store lithium-ion batteries in a discharged condition. Recharge them immediately
after they are discharged. For storing long term, store fully charged
• All batteries gradually lose their charge, even lithium-ion batteries, but the discharge rate
is very low. If the tool is stored for long periods of time without use, recharge the battery
every three to four months and disconnect the battery from the power tool before it is
stored. This practice will prevent the lithium-ion battery being damaged when storewd
Operation
NOTE:
Make sure screwdriver bits used are hardened and suitable for use with an impact
driver.
Fitting a driver bit
1. Pull the Quick Release Mechanism (2) forward and insert the bit into the Quick Release ¼”
(6.35mm) Hex Drive (1)
2. Release the Quick Release Mechanism
3. Pull on the bit to check that it is securely fitted. If the bit is not secure, repeat the above
procedure
Direction control
• The direction of rotation can be set using the Forward/Reverse Selector (3)
• To rotate the impact driver clockwise, push the Forward/Reverse Selector to the left
• To rotate the impact driver anti-clockwise, push the Forward/Reverse Selector to the right
• When the Forward/Reverse Selector is in the central position, the impact driver is locked
• Do not attempt to move the Forward/Reverse Selector when the tool is running
Switching ON
• To start the impact driver, squeeze the Trigger Switch (6). The LED Guide Light (7) will
illuminate automatically
• Further pressure on the Trigger Switch will increase the running speed of the tool
• Practise using the impact driver before using it for normal applications
Note:
It is possible the impact driver may switch off during heavy use due to thermal
protection of the battery and internal components. This may prevent the tool being used again
for a short period of time and does not represent a fault
Accessories
A full range of accessories and products is available from your Triton stockist.
• T12B – T12 1.5Ah Li-Ion Battery 12V
• T12HCB – T12 Hi-Cap 3.0Ah Li-Ion Battery 12V
Additional Triton products compatible with the included batteries:
• T12CH – T12 Combi Hammer Drill 12V
• T12AD – T12 Angle Drill 12V
• T12DD – T12 Drill Driver 12V
• T12RS – T12 Reciprocating Saw 12V
• T12OT – T12 Oscillating Multi-Tool 12V
• T12FL – 12V Swivel Head Torch
725488_Manual.indd 7 03/04/2017 08:56