manualshive.com logo in svg

Tritech Intelligent Gyro Compass, Руководство по эксплуатации продукта


Поделиться
Скачать
background image

Tritech International Ltd

Intelligent Gyro Compass

Symptom

Suggested Action

No   configuration   output  data   from 
iGC ant 19k2 on start-up.

Check that Laptop is set to the correct COM port and that 
the terminal emulator is working OK (do a loopback test by 
shorting pins 2 & 3 of COM port connector on laptop).

No   configuration   output   data   from 
iGC, Laptop checked OK

Open up iGC and check for damage / water ingress and 
status LED function.  When switched on, the green power 
LED should be illuminated.  The green status LED should 
flicker as data is transmitted, the red Reset LED should 
flash once when power is first applied, then go dark.

12.3

Firmware Reprogramming

Occasionally, there may be a requirement to upgrade the embedded firmware inside the iGC.   This 
upgrade may be to update the system to a more recent version that may include additional features, or  
may be to load a custom firmware version for a specific task.

Programming is performed simply by using the Programming & Test cable and a laptop or desktop PC. 
Refer to Appendix K for details of the programming cable.  

The replacement firmware will be provided by Tritech, together with the required PC utility programme 
that is used to transfer the replacement firmware from the PC to the iGC.  Full instructions are always  
supplied with the firmware files, but the following is an outline of the procedure to be followed:

1. Connect up the iGC to the laptop or PC COM port using the Programming cable.
2. Connect a 12-24V DC power supply to the iGC.
3. Ensure that the ‘Direct’ switch is OFF.
4. Switch ON the Programming switch.
5. Run up the programming utility on the laptop or PC.
6. Apply power to the iGC.
7. Transfer the new / replacement .bin file to the iGC using the programming software.
8. Monitor programming progress / status.
9. Once complete, power down the iGC and return the Programming switch to OFF.
10. Power up the iGC and test the revised firmware using a terminal programme, host system 

or the iGC Navigation Display software.

Issue 2

0707-SOM-00004

Page 38 of 51

Содержание Intelligent Gyro Compass



















































Отзывы:

Нет отзывов

Похожие инструкции для Intelligent Gyro Compass

Brunton Omni-Sight User Manual preview
Omni-Sight
Бренд: Brunton Страницы: 8

Бренды по названию

Популярные бренды

Загрузить еще бренды