Tripp Lite NGI-S08C2POE8 Скачать руководство пользователя страница 52

Страница: 52 / 157

4.5.1.2.

ERPS Instance

4.5.1.2.1.

CLI Configuration

Node

Command

Description

enable

show erps instance

This command displays all of the ERPS instance

configurations.

enable

show erps instance

<1-2>

This command displays the specific ERPS instance

configurations.

enable

configure terminal

This command changes the node to configure node.

configure

erps instance

This command enters the instance configure node.

config-erps

-inst

instance <1-2>

control-vlan <1-4094>

data-vlan

VLANLISTS

This command configures a new instance and

specifies its control VLAN and data VLANs.

config-erps

-inst

no instance <1-2>

This command removes an instance.

config-erps

-inst

show

This command displays all of the instance

configurations.

4.5.1.2.2.

Web Configuration

Parameter

Description

Instance Settings

Instance

Configures the instance ID. The valid value is from 1 to 31.

Control VLAN

Configures the control VLAN for the instance. The valid value

is from 1 to 4094.

Data VLAN

Configures the data VLAN for the instance. The valid value is

from 1 to 4094. It can be one or multiple VLANs.

Apply

Click

Apply

to take effect the settings.

Refresh

Click

Refresh

to begin configuring this screen afresh.

Instance Status

Содержание NGI-S08C2POE8






























































































































































Результаты поиска

Содержание NGI-S08C2POE8

Отзывы:

Бренды по названию

Популярные бренды

Tripp Lite NGI-S08C2POE8, Руководство пользователя

Результаты поиска

Содержание NGI-S08C2POE8

Отзывы:

Бренды по названию

Популярные бренды