manualshive.com logo in svg

Tripp Lite NGI-S08C2POE8, Руководство пользователя

Поделиться
Скачать
Tripp Lite NGI-S08C2POE8 Скачать руководство пользователя страница 133

 

133 

 

stp-topology-change 

(disable/enable) 

stp-topology-change trap. 

configure  snmp trap-event 

traffic-monitor 

(disable/enable) 

This command enables/disables thetraffic-monitor 

trap. 

 

8.1.3.2.

 

Web Configuration 

 

 

Parameter 

Description 

Trap Event Settings

 

Select all 

Enables all of trap events. 

Deselect All 

Disables all of trap events. 

Alarm-Over-Heat 

Trap when system’s temperature is too high. 

Alarm-Over-Load 

Trap when system is over load. 

Alarm-Power-Fail  Trap when system power is over voltage/under voltage/RPS over 

voltage/RPS under voltage. 

BPDU-Guard 

Trap when port is blocked by BPDU Guard/BDPU Root 

Guard/BPDU port state changed. 

Loop-Detection 

Trap when port is blocked by Loop Detection. 

Port-Admin-State-

Change 

Trap when port is enabled/disable by administrator. 

Port-Link-Change 

Trap when port is link up/down change. 

STP-Topology-Cha

nge 

Trap when the STP topology change. 

Traffic-Monitor 

Trap when port is blocked by Traffic Monitor. 

Содержание NGI-S08C2POE8






























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды