Tripp Lite NGI-S08C2POE8 Скачать руководство пользователя страница 125

Страница: 125 / 157

125

Rx Utilization (bps)

The field display Rx utilization in bps.

Tx Utilization (%)

The field display Tx utilization in percentage.

Tx Utilization (bps)

The field display Tx utilization in bps.

7.5.

Syslog

The syslog function records some of system information for debugging purpose. Each log

message recorded with one of these levels,

Alert / Critical / Error / Warning / Notice /

Information.

The syslog function can be enabled or disabled. The default setting is disabled.

The log message is recorded in the Switch file system. If the syslog server’s IP address has

been configured, the Switch will send a copy to the syslog server.

The log message file is limited in 2000 entries. If the file is full, the oldest one will be replaced.

7.5.1.

CLI Configuration

Node

Command

Description

enable

show syslog

The command displays all of log message recorded in

the Switch.

enable

show syslog level

<1-6>

The command displays the log message with the level

recorded in the Switch.

enable

show syslog server

The command displays the syslog server

configurations.

enable

configure terminal

This command changes the node to configure node.

configure syslog-server

(disable|enable)

The command disables / enables the syslog function.

configure syslog-server ipv4-ip

IPADDR

The command configures the syslog server’s IP

address.

configure clear syslog

The command clears all of the syslog messages.

configure archive upload-syslog

This command uploads the current syslog message to a

TFTP server.

Where <URL PATH> can be:

ftp://user:[email protected]/file

http://192.168.1.1/file

tftp://192.168.1.1/file

Example:



L2SWITCH#configure terminal



L2SWITCH(config)#syslog-server ip 192.168.200.106



L2SWITCH(config)#syslog-server enable

Содержание NGI-S08C2POE8






























































































































































Результаты поиска

Содержание NGI-S08C2POE8

Отзывы:

Похожие инструкции для NGI-S08C2POE8

Бренды по названию

Популярные бренды

Tripp Lite NGI-S08C2POE8, Руководство пользователя

Результаты поиска

Содержание NGI-S08C2POE8

Отзывы:

Похожие инструкции для NGI-S08C2POE8

Бренды по названию

Популярные бренды