TriMetric TM-2030-A Скачать руководство пользователя страница 1

 

     TriMetric

 

TM-2030 

Battery system monitor, Models TM-2030-RV and TM-2030-A

  

 Technical Manual  

 

INSTALLATION Page 1-7 

USER GUIDE Page 8-23

 

 

revised June 2017 

 

 
IMPORTANT: The wiring installation for this meter, especially the shunt installation 

must be performed by someone knowledgeable in proper wiring, electrical practices, 
and safety. If you do not have this knowledge please have someone install it who does, 
or at least get some competent help to supervise the installation. 

 

 
To install:  

1. Please read or scan two pages of introductory information in section A.  
2. Consult drawings Figure 1 and 2 (pages 7-8). 
3. Follow step by step installation instructions in section B.  
4. Program the two most important parameters into meter (section C1).   

 

A. Before installing the TriMetric meter:

 

B. How to Install Meter and Shunt

:  

C1. How to determine program item P3: “battery system capacity

” 

C2. How to program your meter for the 100A/100mV shunt.

 

C3. Optional: Now or later you may wish to program P4, P5, P6

 

Warranty and customer service 

Limited warranty 

The  TriMetric  TM-2030  is  warranted  for  three  years  against  any  manufacturing  defect.  Any  meter  not  meeting  the 
specification or rated performance shall be replaced or repaired, at Bogart Engineering’s discretion, provided it has not 
been subjected to abuse or misapplication.  For warranty service, please email 

[email protected]

.  A return 

merchandise authorization is required for all merchandise to be returned to Bogart Engineering. 

How to obtain customer service 

Please  review  our  support  page  before  attempting  to  contact  us.    Our  distributors  are  able  to  answer  simple 
questions  about  Bogart  Engineering  products.    For  technical  support,  send  an  email  to 
bogart@bogartengineering and someone will assist you. 

 

BOGART ENGINEERING  

www.bogartengineering.com 

Содержание TM-2030-A
























Отзывы: