TriMark UM 34 Скачать руководство пользователя страница 5

Страница: 5 / 13

Teaching Transmitter FOBs

The keypad is the only method of syncing fobs. The following sequence puts the e-

ASK

module into a “Fob Learn” mode.

1. Press 5/6 button on the keypad for 5 seconds, listen for double beep

a. Keypad backlight continuously flashes on/off

2. Enter the 6-digit authority code and listen for double beep

a. Both keypad LEDs continuously flash amber on/off

3. Press and hold the 7/8 button on the keypad for 5 seconds, listen for double beep

a. Both keypad LEDs illuminate solid amber

b. The e-

ASK

module red & green LEDs will blink rapidly while in learn mode

c. The entrance door is locked, then unlocked rapidly as audible feedback

d. If the e-

ASK

module fails to enter learn mode, the keypad will beep for 2 seconds

indicating the error and steps below will not execute.

e. Fob learn mode is now activated

4. Fob Learn mode

a. The e-

ASK

module stays in fob learn mode for 10 seconds without any button

activity

b. Pressing any button of a fob adds that Fob’s serial number to the “Authorized

Fobs List”

c. Each time a fob is added, the 10 second timer resets

d. When the first fob is added the entire “Authorized fobs list” is erased and a new

one is added. Previously sync’d fobs will not function, thus all desired fobs must

be sync’d in one sequence

e. Each time a fob is successfully added, the entrance door will lock, then unlock

Up to 20 transmitters can be synched with an e-

ASK

module. If more than 20 fobs

attempt to be added, they will over-write the first units programmed.

To exit fob learn mode, wait 10 seconds without pressing any Fob buttons, or press any key on

the keypad. The keypad returns to its normal Learn Mode with both LEDs blinking amber to

indicate it is waiting for the next Learn Mode command. Press 9/0 to exit back to normal

keypad operation.

32-Bit CAN Keypad Operation and Features

The Keypad

is shipped with a default access code and a unique authority code. The authority

code (6 digit) is printed on the product label. Unless the default code has been changed, the

access code is:

Access Code

Authority Code

Code of example shown is 242228

Digit 1 Digit 2

Digit 3

Digit 4

1/2

3/4

5/6

7/8

Содержание UM 34














Результаты поиска

Содержание UM 34

Отзывы:

Похожие инструкции для UM 34

Бренды по названию

Популярные бренды

TriMark UM 34, Инструкция по эксплуатации

Результаты поиска

Содержание UM 34

Отзывы:

Похожие инструкции для UM 34

Бренды по названию

Популярные бренды