background image

SecureMesh

TM

 Extender Bridge 

 

Installation Guide 

Trilliant Incorporated 

page 18 of 26 

Attach The Extender Bridge to the Bracket

 

Use the provided mounting bracket and appropriate length 
¼

―diameter screws that are provided in the accessory kit to 

attach the SecureMesh Extender Bridge to the mounting pole 
(see the figure on the right). 

Before tightening, rotate the device to ensure there is ample 
room for the omnidirectional antennas to clear the mount 
stand and streetlight pole. 

 

 

Attach the Ground Wire

 

  Connect the Ethernet PoE cable to the Ethernet port at 

the base of the Extender Bridge, pushing the 8P8C into 
the socket on the bottom of the Extender Bridge until it 
locks into place (as shown on the right).  The Ethernet 
PoE cable should be routed through the water protection 
gasket. 

  Loosen the ground screw at the base of the Extender 

Bridge.  Remove a section of the insulation on the ground 
wire that will attach to the ground point on the streetlight, 
and wrap this section around the ground screw and 
tighten the screw. 

  If the streetlight is completely metal, attach the other end 

of the ground wire to the mounting hardware.  If the 
streetlight is a metal arm attached to a wooden pole the 
ground wire must extend to a proper ground location. 

 

 

 

Ethernet PoE cable 

ground 
wire 

8P8C Ethernet 

socket 

8P8C 
serial port 

View of underside with cover plate removed 

water intrusion 

gasket 

Содержание SecureMesh



























Отзывы: