background image

SecureMesh

TM

 Extender Bridge 

 

Installation Guide 

Trilliant Incorporated 

page 17 of 26 

Streetlight Pole Mounting and Grounding 

To install an Extender Bridge on a streetlight, observe the following procedures: 

 

Mounting the Device 

 

Mount the Bracket

 

  Chose one of the two available Streetlight Installation 

Kits from the Extender Bridge accessory list.  The kits 
vary only in the length of the cable to attach to the 
streetlight photo cell. 

  If the clamp is not already separate from the main 

bracket, remove the nuts from the bolts and separate 
the clamp from the main bracket. 

  Place the main bracket over the 

light pole’s horizontal 

extension arm.  Place the clamp on the bolts and 
secure with the nuts provided as shown on the right. 
Hand tighten the nuts. 

  Make the mounting pipe plumb (straight) by moving the 

main bracket from side to side and moving the plumb 
adjustment bracket forward and backward. The 
accuracy should be checked using a magnetic level. 
When the mounting pipe is plumb, tighten all nuts. 

 

 

 

 

 

 

photo cell tap 

AC input 

excess wire storage 

clamp 

Ethernet  
PoE cable 

power supply and 
surge protection 

plumb adjustment bracket  

main bracket 

mounting pipe 

plumb adjustment screw  

Содержание SecureMesh



























Отзывы: