background image

SecureMesh

TM

 Extender Bridge 

 

Installation Guide 

Trilliant Incorporated 

page 13 of 26 

Grounding and Protecting the Device

   

 

The surge protector box should be attached to the 
bottom of the Extender Bridge.  The surge protector will 
be attached using the ground screw as a pivot point 
then the box will be swung into place against a mounting 
bracket screw. 

  Remove the ground screw from the base of the 

device, and then loosen (but do not remove) the 
screw on the same side of the bracket as the 
ground screw 

  Run the ground screw through the lug of the green 

ground wire coming from the surge protector and 
the hole in the surge protector bracket. 

  Before tightening the ground screw, remove a 

section of the insulation on the ground wire which 
will attach to the ground point on the mounting 
structure and wrap this section around the ground 
screw. 

  Pivot the box into place such that the other end of 

the surge protector’s mounting bracket touches the 
loosened screw.  Tighten both screws. 

  Be sure to connect the ground wire to the 

grounding point on the mounting structure. 

  Run the CAT5e cable under the gasket and plug it 

into the Ethernet port in the cavity on the device 
base (see the diagram to the right) 

 

 

 

 

.

 

CAT5e 

Ethernet Cable 

8P8C Ethernet 
Port 

8P8C serial 
port 

View of underside with cover plate removed 

ground wire 

ground wire to 
mounting 
structure 

ground screw 

Содержание SecureMesh



























Отзывы: