Trilithic 180 DSP Скачать руководство пользователя

Страница: 57 / 386

www.trilithic.com

Page I-38

180 DSP Operation Manual

Signal Level Meter

Perform the following steps to connect using the Ethernet connection:

1. Connect an Ethernet cable to the

Ethernet port of the 180 DSP.

2. Select the

Ethernet

connection

button from the

Network Manager

window as shown in the image to

the right.

Ethernet Connection

3. If the

Prompt User

option is set

Yes

from within the

Ethernet

Settings

option of the

Setup

menu, the

Ethernet Settings

window will appear as shown in

the image to the right. Adjust the

Ethernet settings as desired and

then select the

Login

button.

If the Prompt User option is set to No from within the Ethernet

Settings option of the Setup menu, the Ethernet Settings

window will not appear. If so, proceed to Step 4.

Содержание 180 DSP



































































































































































































































































































































































































Результаты поиска

Содержание 180 DSP

Отзывы:

Похожие инструкции для 180 DSP

Бренды по названию

Популярные бренды

Trilithic 180 DSP, Руководство по эксплуатации

Результаты поиска

Содержание 180 DSP

Отзывы:

Похожие инструкции для 180 DSP

Бренды по названию

Популярные бренды