Trilithic 180 DSP страница 359 Скачать руководство пользователя

Страница: 359 / 386

www.trilithic.com

Page IV-163

180 DSP Operation Manual

Signal Level Meter

Other Settings

The

Background

setting of the display can be either

Dark

Light

. Adjust this for the best

readability of the display.
The

Persistence

setting can be a value from

, selectable in multiples of two

(1,2,4,8,16,32). This value has a direct effect on the number of samples used to build the

specific traces. The end effect of this setting is the higher the value, the longer the max

trace stays visible. A suggested value for this field is 8 or 16.

Measurement Mode

The Traffic Control Plus spectrum

has two measurement modes:

Marker

mode and

Region of

Interest

mode. The marker mode

allows the user to move a marker to

any frequency and display the values

of the three traces at that frequency,

as shown in the image to the right.

In the region of interest measurement

mode, you can define a center

frequency and a span, such as a

cable modem channel. The traffic

level, signal to noise ratio, and

channel utilization will be calculated

for that region. Please note that the

region of interest measurements are

only valid for bursty signals.

Содержание 180 DSP



































































































































































































































































































































































































Результаты поиска

Содержание 180 DSP

Отзывы:

Похожие инструкции для 180 DSP

Бренды по названию

Популярные бренды

Trilithic 180 DSP, Руководство по эксплуатации

Результаты поиска

Содержание 180 DSP

Отзывы:

Похожие инструкции для 180 DSP

Бренды по названию

Популярные бренды