Trilithic 180 DSP Скачать руководство пользователя страница 326

Страница: 326 / 386

www.trilithic.com

Page IV-130

180 DSP Operation Manual

Signal Level Meter

Selecting a Favorite

After entering a destination IP address as

shown in the previous section, the 180 DSP

allows you to save the entered IP address as

a favorite location for quick and easy access.
Select the

Favorites

softkey to view a

list of up to six (6) favorite destination IP

addresses.
From the

Favorites

pop-up menu, select the

name of the favorite to use for testing. The IP

address or URL of the selected location will

be entered automatically in the

field.

Executing Network Tests

After entering a destination IP address or

selecting a favorite, select the

Start

key to

execute the selected test.
The 180 DSP will display the measurement

results for each test mode as shown in the

following sections.

Содержание 180 DSP



































































































































































































































































































































































































Результаты поиска

Содержание 180 DSP

Отзывы:

Бренды по названию

Популярные бренды

Trilithic 180 DSP, Руководство по эксплуатации

Результаты поиска

Содержание 180 DSP

Отзывы:

Бренды по названию

Популярные бренды