Trilithic 180 DSP Скачать руководство пользователя

Страница: 316 / 386

www.trilithic.com

Page IV-120

180 DSP Operation Manual

Signal Level Meter

Test Point Compensation

Select the

Test Point Compensation

button from the

Function

enter test point loss measurements

for both test point and probe loss.
The

Test Point

screen will be

displayed as shown in the image to

the right.

Test Point Loss

Highlight the

Test Point

field and

then use either of the following

methods to change the loss value:

• Use the up/down arrow

buttons to change the test

point loss level in 1 dB

increments.

• Press the

Enter

button and

use the

Virtual Keyboard

to directly enter the loss

value as shown in the

image to the right.

Содержание 180 DSP



































































































































































































































































































































































































Результаты поиска

Содержание 180 DSP

Отзывы:

Похожие инструкции для 180 DSP

Бренды по названию

Популярные бренды

Trilithic 180 DSP, Руководство по эксплуатации

Результаты поиска

Содержание 180 DSP

Отзывы:

Похожие инструкции для 180 DSP

Бренды по названию

Популярные бренды